Announcement

Collapse
No announcement yet.

Jon00 Control INI programming... one quick Q for those who have done it.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Jon00 Control INI programming... one quick Q for those who have done it.

    It seems like as I go down the iPhone sample INI and modify for my UPB devices (using the X10 commands) everything works fine as long as I don't remve a device or leave some setting blank for a button. If I do this, my other devices below this button properly display status, but the button itself will not activate the device. It refreshes but never activates. Example below:

    On Column 1 Table 10 Button 1 I want to leave it blank as a palceholder for a future light. Removing the info after '=' causes the button to not appear, as I expect, but then everything below this (Master Bedroom) does not activate the ligths even though a correct device code is used. Putting that same device code in the DisplayTags declarations on bottom properly shows the status of the device on the button as on, off or percentage, but the button no longer works. So I guess what I'm asking is if this is expected behavior, and if so, how do I skip a button or remark out a button for future use without disabling all future buttons on the page? Otherwise I'm loving this alternative for a simple HSTouch replacement.

    Thanks!!!

    ---Column 1 Table 9 Button 1---
    Button9-1Type=Dimmer39
    Button9-1Text=Cabinet Lights
    Button9-1Action=X10Toggle \19,DDim,H,5,255,500,540,50,50
    ---Column 1 Table 9 Button 2---
    Button9-2Type=spacer 66,50,#000000,#FFFFFF,10pt,Helvetica,,middle,center,0,0,5,5, 5,5
    Button9-2Text=[Displaytag9]
    ---Column 1 Table 10---
    Heading10=null
    ---Column 1 Table 10 Button 1---
    Button10-1Type=
    Button10-1Text=
    Button10-1Action=
    ---Column 1 Table 10 Button 2---
    Button10-2Type=spacer 66,50,#000000,#FFFFFF,10pt,Helvetica,,middle,center,0,0,5,5, 5,5
    Button10-2Text=[Displaytag10]
    +++++ End Kitchen +++++

    +++++ Start Master bedroom +++++
    ---Column 1 Table 11---
    Table11SpacerTop=10
    Table11SpacerBottom=0
    Table11BackgroundHeight=0
    Table11BackgroundWidth=1
    Table11BackgroundColor=
    Table11FontColor=#FFFFFF
    Table11FontSize=12px
    Table11DescPadding=
    Column 1 TableHeading 11---
    Heading11FontSize=12pt
    Heading11FontColor=#FFFFFF
    Heading11BackgroundColor=#4c566c
    Heading11padding=
    Heading11Radius=15,15,0,0
    Heading11=<b>Master bedroom</b>
    ---Column 1 Table 11 Button 1---
    Button11-1Type=Dimmer26
    Button11-1Text=Overhead Lights
    Button11-1Action=X10Dimmer \22,DDim,H,5,255,630,675,85,15
    ---Column 1 Table 11 Button 2---
    Button11-2Type=spacer 66,50,#000000,#FFFFFF,10pt,Helvetica,,middle,center,0,0,5,5, 5,5
    Button11-2Text=[Displaytag11]
    ---Column 1 Table 12---
    Heading12=null
    ---Column 1 Table 12 Button 1---
    Button12-1Type=Dimmer27
    Button12-1Text=Bed Lamps
    Button12-1Action=X10Dimmer \38,DDim,H,5,255,683,725,85,15

    #2
    You cannot have empty button fields. They have to be defined by one of the six types as defined in the instructions.

    As you just want a place holder, add a spacer which is set to the same size as the existing button i.e.

    Button10-1Type=spacer 66,50
    Jon

    Comment

    Working...
    X