Hey All,
Dusting of my old HS system after recently moving house.
Have been playing around with some new Arduino configurations for various things I would like to interface with, and have started getting some odd behaviour from the Plugin.
If I do the following.
1) Create a New Board, using Com5
2) Upload the Sketch using the Arduino IDE, with success.
3) Try connecting using the 'connect' button either in the device management screen, or the Plugin screen it simply stays disconnected.
4) Select 'AutoConnect' and away it goes, no issues at all....
I can see in the logs this soon after I press 'connect'
- Board 1 Version 1.0.0.127 and Plugin Version 1.0.0.131 are compatible.
But nothing further happens.
When I de-select, then re-select the 'Auto Connect' option, i see this.
- Connected to Board No:1 on COM5
- Updating pins on Board No: 1
- Updating Values on Board No: 1
- setting Board 1 ID 715 to Auto Connect
The Home seer logs show pretty much what I've shown above.
The Plugin logs I created show;
7/9/2021 ,14:20:32.278 Data Received:Version 1 1.0.0.127 HS3
7/9/2021 ,14:20:32.290 Board 1 Version 1.0.0.127 and Plugin Version 1.0.0.131 are compatible.
7/9/2021 ,14:20:32.311 Sent to com port No:5 = 1 C ,Connect Command
7/9/2021 ,14:20:32.383 Data Received:Conneced 1
Now, to me it looks like an unrecognised character in the last line, from here nothing more happens.
When I connect using the 'Auto Connect option, this response is normal, and the cycle continues no problems;
7/9/2021 ,14:20:54.743 postBackProc AutoConnect1=checked&id=AutoConnect1
7/9/2021 ,14:20:54.749 Data Received:Connected 1
7/9/2021 ,14:20:54.754 Connected to Board No:1 on COM5
7/9/2021 ,14:20:54.825 Updating pins on Board No: 1
No unrecognised Character.....
I feel this is part of my problem, but cannot find a way to fix it.
- Tried different ports
- Tried different UNO Boards
- I've tried uninstalling and re-installing the plugin.
- I've tried re-installing HS. (Not clean, just repair)
(Yet to try over ethernet)
The problem remains.
Any suggestions on steps to rectify, or explanation as to what is going on would be much appreciated
Many Thanks in Avdance,
Steve Button
--------------------------------------------------
HS system detail below, Logs attached
--------------------------------------------------
Current Date/Time: 7/09/2021 2:41:24 PM
HomeSeer Version: HS3 Pro Edition 3.0.0.548
Operating System: Microsoft Windows 10 Pro - Work Station
System Uptime: 0 Days 0 Hours 22 Minutes 40 Seconds
IP Address: 192.168.1.105
Number of Devices: 38
Number of Events: 109
Available Threads: 400
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed: Windows Defender
In Virtual Machine: No MFG: hewlett-packard
Enabled Plug-Ins
1.0.0.131: Arduino Plugin
1.0.3.0: BLShutdown
3.7.0.0: Harmony Hub
3.7.0.0: Harmony Hub
3.0.7.0: Z-Wave
Dusting of my old HS system after recently moving house.
Have been playing around with some new Arduino configurations for various things I would like to interface with, and have started getting some odd behaviour from the Plugin.
If I do the following.
1) Create a New Board, using Com5
2) Upload the Sketch using the Arduino IDE, with success.
3) Try connecting using the 'connect' button either in the device management screen, or the Plugin screen it simply stays disconnected.
4) Select 'AutoConnect' and away it goes, no issues at all....
I can see in the logs this soon after I press 'connect'
- Board 1 Version 1.0.0.127 and Plugin Version 1.0.0.131 are compatible.
But nothing further happens.
When I de-select, then re-select the 'Auto Connect' option, i see this.
- Connected to Board No:1 on COM5
- Updating pins on Board No: 1
- Updating Values on Board No: 1
- setting Board 1 ID 715 to Auto Connect
The Home seer logs show pretty much what I've shown above.
The Plugin logs I created show;
7/9/2021 ,14:20:32.278 Data Received:Version 1 1.0.0.127 HS3
7/9/2021 ,14:20:32.290 Board 1 Version 1.0.0.127 and Plugin Version 1.0.0.131 are compatible.
7/9/2021 ,14:20:32.311 Sent to com port No:5 = 1 C ,Connect Command
7/9/2021 ,14:20:32.383 Data Received:Conneced 1
Now, to me it looks like an unrecognised character in the last line, from here nothing more happens.
When I connect using the 'Auto Connect option, this response is normal, and the cycle continues no problems;
7/9/2021 ,14:20:54.743 postBackProc AutoConnect1=checked&id=AutoConnect1
7/9/2021 ,14:20:54.749 Data Received:Connected 1
7/9/2021 ,14:20:54.754 Connected to Board No:1 on COM5
7/9/2021 ,14:20:54.825 Updating pins on Board No: 1
No unrecognised Character.....
I feel this is part of my problem, but cannot find a way to fix it.
- Tried different ports
- Tried different UNO Boards
- I've tried uninstalling and re-installing the plugin.
- I've tried re-installing HS. (Not clean, just repair)
(Yet to try over ethernet)
The problem remains.
Any suggestions on steps to rectify, or explanation as to what is going on would be much appreciated
Many Thanks in Avdance,
Steve Button
--------------------------------------------------
HS system detail below, Logs attached
--------------------------------------------------
Current Date/Time: 7/09/2021 2:41:24 PM
HomeSeer Version: HS3 Pro Edition 3.0.0.548
Operating System: Microsoft Windows 10 Pro - Work Station
System Uptime: 0 Days 0 Hours 22 Minutes 40 Seconds
IP Address: 192.168.1.105
Number of Devices: 38
Number of Events: 109
Available Threads: 400
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed: Windows Defender
In Virtual Machine: No MFG: hewlett-packard
Enabled Plug-Ins
1.0.0.131: Arduino Plugin
1.0.3.0: BLShutdown
3.7.0.0: Harmony Hub
3.7.0.0: Harmony Hub
3.0.7.0: Z-Wave
Comment