When I connecting an Arduino board by USB One-Wire temperature sensors work good. If I try to use IP with a network card, board connects but no temperatures show up. Have tried Uno and Mega boards. What am I doing wrong? I would like multiple boards to be connected.
-
-
Which Arduino board? What pin are you using for OneWire?HS4 Pro, 4.2.19.0 Windows 10 pro, Supermicro LP Xeon -
Using either Uno or Mega on input 3Comment
-
If by input 3 you mean digital input pin 3, that should work. I use pin 23 on my 4 Megas, but any digital pin should work. There are some pins blocked by the Ethernet shield. They are 10-13 IIRC.HS4 Pro, 4.2.19.0 Windows 10 pro, Supermicro LP XeonComment
-
Yes, digital input 3. I just tried input 23, as well, no difference. I'm wondering if I have setup IP correctly. Is IP address the same as Homeseer or a different one? Is MAC address random or should it be something specific?Comment
-
The plug-in assigns arbitrary MAC addresses. You have to pick an open IP within your subnet to assign to the board. The plug-in cannot detect conflicts, so you have to pick an open one.HS4 Pro, 4.2.19.0 Windows 10 pro, Supermicro LP XeonComment
-
Ok, it looks like its connected but I'm still not getting any temperature readings. After being connected for a few minutes, it comes back with connection failed.Comment
-
Can you get me a debug file so I can see what is wrong. Please do the following:Originally posted by garypcollins@rogers.com View Post- Go to the plugin settings page and then check the debug tick box.
- Go to the board in the device manager and press connect.
- wait 5min.
- Go back to the settings page and turn off debugging
- click the link that is created on that page to download the debug file.
- There is an email link at the top of that page. Click it and Send the debug file to me.
- Post here to say you have sent it.
Zwave = Z-Stick, 3xHSM100� 7xACT ZDM230, 1xEverspring SM103, 2xACT HomePro ZRP210.
X10 = CM12U, 2xAM12, 1xAW10, 1 x TM13U, 1xMS13, 2xHR10, 2xSS13
Other Hardware = ADI Ocelot + secu16, Global Cache GC100, RFXtrx433, 3 x Foscams.
Plugings = RFXcom, ActiveBackup, Applied Digital Ocelot, BLDeviceMatrix, BLGarbage, BLLAN, Current Cost, Global Cache GC100,HSTouch Android, HSTouch Server, HSTouch Server Unlimited, NetCAM, PowerTrigger, SageWebcamXP, SqueezeBox, X10 CM11A/CM12U.
Scripts = Various
Comment
-
Debug file sentComment
-
garypcollins@rogers.com I sent you a reply did you get it? I was also confused about the post as this is for the HS3 version of the plugin but you are running the HS4. Please Post HereZwave = Z-Stick, 3xHSM100� 7xACT ZDM230, 1xEverspring SM103, 2xACT HomePro ZRP210.
X10 = CM12U, 2xAM12, 1xAW10, 1 x TM13U, 1xMS13, 2xHR10, 2xSS13
Other Hardware = ADI Ocelot + secu16, Global Cache GC100, RFXtrx433, 3 x Foscams.
Plugings = RFXcom, ActiveBackup, Applied Digital Ocelot, BLDeviceMatrix, BLGarbage, BLLAN, Current Cost, Global Cache GC100,HSTouch Android, HSTouch Server, HSTouch Server Unlimited, NetCAM, PowerTrigger, SageWebcamXP, SqueezeBox, X10 CM11A/CM12U.
Scripts = Various
Comment
-
Posted on Enigmatheatre forumComment
Comment