Hi Hurry4it,
I just installed your SimpleHomeNet version 2.0.0.0 into HomeSeer version 3.0.0.96. Then using your plugin I installed an EZIO40. It seemed to install but I somehow added 2 devices. One was correctly added and the other one had an error. Again using your plugin I tried to delete the wrong device. It did not happen. I can not delete it. Later I found an entry in the HomeSeer log like the one below. I am not certain if it was about the delete process or something else.
Aug-26 4:24:14 PM SimpleHomeNet Error An unexpected error occured in the SetIOMulti() function/subroutine: [System.IndexOutOfRangeException: Index was outside the bounds of the array. at HSPI_SIMPLEHOMENET.HSPI.SetIOMulti(List`1 colSend)]
Aug-26 4:24:14 PM Device Control Device: Great Room Root Device to Diagnostic On (100) by/from: CAPI Control Handler
Also I can not control any of the 4 outlets using your plugin. I must be doing something wrong. So I began looking for information on your plugin. I have not been able to find any. I did find a Thread where you stated that you were soon publishing detailed information on the installation and use of the SimpleHomeNet plugin and I believe that thread was written last summer but I haven't been able to find it. In this thread I found a reference to a download site where I thought perhaps I could find some information but when I click on the link it went to a generic site. It had been redirected. The reference I am speaking of is the one below. Could you perhaps post the current site for the below guide for others to find it. And perhaps it has some information that would provide me with some guidance.
http://www.simplehomenet.com/Downloa...ct%20Guide.pdf
If you have any information on these questions it would be greatly appreciated.
Where can I find the documentation for the SimpleHomeNet.
What was the reason for the above log entry?
Why couldn't I delete the "bad entry" with the plugin?
Why can't I change the outputs of the EZIO40?
Any assistance would be greatly appreciated.
Thanks,
Bruce
I just installed your SimpleHomeNet version 2.0.0.0 into HomeSeer version 3.0.0.96. Then using your plugin I installed an EZIO40. It seemed to install but I somehow added 2 devices. One was correctly added and the other one had an error. Again using your plugin I tried to delete the wrong device. It did not happen. I can not delete it. Later I found an entry in the HomeSeer log like the one below. I am not certain if it was about the delete process or something else.
Aug-26 4:24:14 PM SimpleHomeNet Error An unexpected error occured in the SetIOMulti() function/subroutine: [System.IndexOutOfRangeException: Index was outside the bounds of the array. at HSPI_SIMPLEHOMENET.HSPI.SetIOMulti(List`1 colSend)]
Aug-26 4:24:14 PM Device Control Device: Great Room Root Device to Diagnostic On (100) by/from: CAPI Control Handler
Also I can not control any of the 4 outlets using your plugin. I must be doing something wrong. So I began looking for information on your plugin. I have not been able to find any. I did find a Thread where you stated that you were soon publishing detailed information on the installation and use of the SimpleHomeNet plugin and I believe that thread was written last summer but I haven't been able to find it. In this thread I found a reference to a download site where I thought perhaps I could find some information but when I click on the link it went to a generic site. It had been redirected. The reference I am speaking of is the one below. Could you perhaps post the current site for the below guide for others to find it. And perhaps it has some information that would provide me with some guidance.
http://www.simplehomenet.com/Downloa...ct%20Guide.pdf
If you have any information on these questions it would be greatly appreciated.
Where can I find the documentation for the SimpleHomeNet.
What was the reason for the above log entry?
Why couldn't I delete the "bad entry" with the plugin?
Why can't I change the outputs of the EZIO40?
Any assistance would be greatly appreciated.
Thanks,
Bruce
Comment