how do I add my own IR commands to HS

[I-1]

Hi,

I have created a list of commands in Homeseer for my Infra Red device (XBOX 360)
I am using signal location 157 - 183 for all of the keys I need for controlling the XBOX 360.

Now I dont have the XBOX 360 remote (and I don't want to buy it either) but I found the IR commands on a website.

Now I see the Discrete ON and Descrete OFF fpr example:

Discrete ON

0000 0073 0044 0000 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0030 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0020 0010 0010 0010 09bd 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0030 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0020 0010 0010 0010 0020

Discrete OFF

0000 0073 0044 0000 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0030 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0020 0010 0010 0010 09bd 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0030 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0020 0010 0010 0010 0020

How do I add these commands into the homeseer under the signal locations?

I want to use signal location 158 for the Discrete ON and use 159 for the Discrete OFF.

Thanks,

[I-1]

Is there nobody who can answer this question?

[Rupp]

Did you contact the plugin author via his support email addr?
See this post for a link to his forum.
http://board.homeseer.com/showthread.php?t=112929

[I-1]

I have it working now ...

[Rupp]

I have it working now ...

Any hits for future searches?

[I-1]

I used a logitech harmony to learn the commands from

[DomeAdept]

You can add these codes directly by using the CCF option:
Create the IR device/actions in homeseer's IR page but don't learn any signal (and remember the position numbers).
Open de HS2-signals.rem file in the Irtrans/remotes dir.
Locate the position number of the just created device/actions and add you custom codes so you end up with lines looking like this (lines are truncated):

[72][CCF]0000 006C 0044 0000 0157 00AD 0016 0015 0016 0040 0016
[73][CCF]0000 006C 005F 0001 0157 00AD 0016 0015 0016 0040 0016
[74][CCF]0000 006C 0026 0000 0157 00AD 0016 0015 0016 0040 0016
[75][CCF]0000 006D 0022 0002 0156 00AB 0015 0015 0015 003F 0015
[70][CCF]0000 006C 0026 0000 0157 00AD 0016 0015 0016 0040 00

And Bob's your uncle....

(these codes are referred to as Pronto codes, for the older Philips Pronto Universal Remotes)