Announcement

Collapse
No announcement yet.

Hub randomly disconnects

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • sirmeili
    replied
    Originally posted by grtaylor View Post
    Thanks. Will give it a try. I have a multi access point Unifi network, and I was wondering if perhaps the hub is switching AP's and goes dead then. I'll keep an eye on which AP it is connected to and if it changes.
    I run unifi, what I did was create a 2.4ghz network and assigned it to only 1 AP that all my hubs can reach. This solved some of my issues with some of my hubs.

    Leave a comment:


  • grtaylor
    replied
    Thanks. Will give it a try. I have a multi access point Unifi network, and I was wondering if perhaps the hub is switching AP's and goes dead then. I'll keep an eye on which AP it is connected to and if it changes.

    Leave a comment:


  • sirmeili
    replied
    If you were using the "production" version, it was for some reason still .16 even though I know I submitted .18 for approval. For now I have increased the version number on both the production and the beta to 3.1.0.19 and pushed it up. You can access the beta now, the production one tomorrow. They are the same exact version.

    Note that post .16 I had some connection fixes in there that might help you.

    Leave a comment:


  • grtaylor
    replied
    Were you able to post a new version that might help this disconnect issue yet? I see this issue pretty regularly. Restarting the PI works, but something better would be preferable.
    Jun-03 7:13:37 AM Error The Connection to Hub with ID 9d18ee2366522f92202bdc96ec249707d3244d23 failed with stack trace: at System.Net.Sockets.TcpClient..ctor(String hostname, Int32 port) at HarmonyHub.Client.Connect(Int32 heartbeatInterval)
    Jun-03 7:13:37 AM Error The Connection to Hub with ID 9d18ee2366522f9202bdc96ec249707d3244d23 failed with message: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond 192.168.1.149:5222

    Leave a comment:


  • sirmeili
    replied
    Just a note that having it work on HS4 is a low priority of mine. That said, I think there was a mixup with what I put up there for .18 and somehow it ended up being .16 (Which had the problem you are describing). I will be uploading the correct version tonight or tomorrow night.

    Leave a comment:


  • Papatufan
    replied
    I also have the problem that, at some time, the plug-in disconnects. Can’t connect and have to restart homeseer to get the plugin working again. Using plugin version 3.1.0.18 with betaversion HS4. I also intend on keeping on using your plugin. I am a Dutch user of your plugin.

    Leave a comment:


  • ts1234
    replied
    Thanks for the update and so glad to hear you'll keep working on this!!! ...and I'll be honest here. I'm very torn on my feelings between what an automation product should do inherently and all the work developers do for their products that make them attractive before they are.

    +1 on keeping on using your plugin...

    Leave a comment:


  • MattL0
    replied
    I plan to keep this plugin... since it has more fonction.

    Leave a comment:


  • MattL0
    replied
    An hs4 version would be only usefull when (and if) hs4 really extend the fonctions of hs3

    Leave a comment:


  • sirmeili
    replied
    Yes, life has been settling down. I've been going over the new plugin's code (From simplextech) and looking into bugs in my existing plugins. I don't have any releases ready yet for bugs like this, but I'm still looking at that rewrite.

    As far as HS4 goes, HST wrote their own version for HS4. I have tried mine and as is it works Ok, but not great. Mine does have more features than theirs, but if you aren't using those features I guess their's is the way to go for HS4.

    As of right now I don't have any plans to create a whole new HS4 version (Because HS4 plugins are not backwards compatible it would mean I have to support 2 separate versions), but since HS3 plugins are supposed to work, mine should work fine in HS4. I haven't done extensive testing though.

    Leave a comment:


  • joegr
    replied
    My understanding is that HS4 will include Harmony hub control. I don't know if it will be based on this plugin or something completely different.
    It looks (but I certainly don't know) like support for this plugin has reached an end...

    Leave a comment:


  • ts1234
    replied
    I hate to ask since you've clearly been busy at your "'real job" and it's been the holiday season too.

    This is one of my favorite and most used plugins... Over the last month or a little more this has been hanging more than it's been working for me. I use it in conjunction with an older iPad and HSTouch. It's a wonderfully powerful combination that beats the crap out of any remote you can buy. It didn't used to hang, or if it did I never isolated it to the plugin as it happened rarely. These posts seemed to have started about the same time. That could just be a coincidence, but does seem kind of relevant? Other things controlled via the iPad and HSTouch keep working. Shutting down and restarting the plugin only works sometimes and often even when it does it stops again shortly afterwards. So a few quick q's...

    Did Harmony change something again as well?
    Any idea when the rewrite will be available?
    And one obvious one...When it clears the connection out it will fully reestablish it automatically?

    and...not meaning to be too pushy (really since I know this has to chew up a ton of your time)...but will there be an HS4 version as well soon? I hate to ask that but I'm thinking of rebuilding my whole install when HS4 comes out as there are a number of things I would do differently after a couple year of using HS3. Since there are so many control functions that have to be rebuilt on the iPAD/HSTouch/This plugin (it took me almost a whole day to rebuild this once) it'd be great to have some idea of any timelines. If there's not one yet, that's fine too...so just asking.

    Thanks!

    Leave a comment:


  • JohnS
    replied
    Originally posted by sirmeili View Post

    will check this out. My workload has started to go own at my day job so i'm hoping to start jumping into the plugins really soon.
    Thanks Sirmeli.

    Probably once a day a hub randomly disconnects and I have to disable and re-enable the plugin to get it working again.

    Leave a comment:


  • sirmeili
    replied
    Originally posted by JohnS View Post

    While I wait for your solution, I am going to try a temporary solution by disabling and re-enabling the plugin when it disconnects.

    Any thoughts on this issue:
    I also noticed that on the Device Config page, that when I select either of my hubs nothing happens. I'm not sure what is supposed to happen, but I assume that some configuration options will appear once you select a hub.
    will check this out. My workload has started to go own at my day job so i'm hoping to start jumping into the plugins really soon.

    Leave a comment:


  • JohnS
    replied
    Originally posted by sirmeili View Post
    please bear with me while I try and carver out time from this. My project's deadline at work was pushed back, but I'm hoping that comes with lighter workdays to give me more time with family and for stuff like working on the plugins (which I genuinely enjoy)
    While I wait for your solution, I am going to try a temporary solution by disabling and re-enabling the plugin when it disconnects.

    Any thoughts on this issue:
    I also noticed that on the Device Config page, that when I select either of my hubs nothing happens. I'm not sure what is supposed to happen, but I assume that some configuration options will appear once you select a hub.

    Leave a comment:

Working...
X