Issues fixed
Looks good - both the master and slave devices now correctly display the offline condition.
Thanks!
Announcement
Collapse
No announcement yet.
UPS Status device value incorrect in some cases
Collapse
X
-
Try to install it again rom the updater. They resolved the issue.
Sent from my iPad using Tapatalk
Leave a comment:
-
Hi,
Same error here. But nevertheless, the plugin was disabled before update.
Leave a comment:
-
I'm getting 'Wrong Local header signature' on the update:
Code:Oct-09 12:33:56 PM Updater Install/Update of package APCUPSD failed. Oct-09 12:33:56 PM Updater Error Installation of package APCUPSD failed. Try disabling the plugin first, then re-try the update. Oct-09 12:33:56 PM Updater Error Unable to open install.txt file for update C:\Program Files\HomeSeer HS3\Updates3\APCUPSD3.2.0.5 Oct-09 12:33:56 PM Error Error unzipping C:\Program Files\HomeSeer HS3\Updates3\APCUPSD3.2.0.5\HSPI_APCUPSD_3.2.0.5.zip, Wrong Local header signature: 0x4F44213C on line 0 Oct-09 12:33:56 PM Updater Installing package APCUPSD
Leave a comment:
-
Originally posted by zwolfpack View PostSituation where the USB gets disconnected. See image 1 & 2 in 1st post. The staus flag value is actually COMM_LOST. Seems like the status device should show 'Offline' rather than 'Charging'.
Check the latest version in the updater. It should resolve this issue.
Sent from my iPad using Tapatalk
Leave a comment:
-
Situation where the USB gets disconnected. See image 1 & 2 in 1st post. The staus flag value is actually COMM_LOST. Seems like the status device should show 'Offline' rather than 'Charging'.
Leave a comment:
-
Slave looks good - matches the master.
No comm event still show "charging" instead of "offline" for both master & slave.
Leave a comment:
-
Originally posted by zwolfpack View PostI should make clear that I have two UPS's. Each is connected to a Windows box, and both behave the same. The Rpi is slaved off one of the Windows boxes. So its safe to ignore UPS1 in attached.
(As a side note, I verified that the Rpi can act as a master, with the Windows box slaved to that. The behavior of the plugin is the same; master shows charging when offline, and slave always shows charging).
Check the updated version in the updater. It should update the status value if master/slave setup is used.
Sent from my iPad using Tapatalk
Leave a comment:
-
Originally posted by zwolfpack View PostI should make clear that I have two UPS's. Each is connected to a Windows box, and both behave the same. The Rpi is slaved off one of the Windows boxes. So its safe to ignore UPS1 in attached.
(As a side note, I verified that the Rpi can act as a master, with the Windows box slaved to that. The behavior of the plugin is the same; master shows charging when offline, and slave always shows charging).
Thank and will look at it (will take a few days)
Leave a comment:
-
Originally posted by pcp View PostThe two devices are actually driven by two separate fields received from the apcupsd software. The Status device value is driven by a STATUS received from apcupsd, while the Status Flags device value comes from the STATFLAG. If you enable debug mode in the plugin, it will display in the HS3 log file the underlying updates received from the apcupsd software (for example for STATUS and STATFLAG). Can you enable it and post the values from the HS3 log of what is sent by the apcupsd software for each of the three UPS?
(As a side note, I verified that the Rpi can act as a master, with the Windows box slaved to that. The behavior of the plugin is the same; master shows charging when offline, and slave always shows charging).Attached FilesLast edited by zwolfpack; September 16, 2016, 12:02 AM. Reason: replace attachment with updated UPS3 entries
Leave a comment:
-
The two devices are actually driven by two separate fields received from the apcupsd software. The Status device value is driven by a STATUS received from apcupsd, while the Status Flags device value comes from the STATFLAG. If you enable debug mode in the plugin, it will display in the HS3 log file the underlying updates received from the apcupsd software (for example for STATUS and STATFLAG). Can you enable it and post the values from the HS3 log of what is sent by the apcupsd software for each of the three UPS?
Leave a comment:
-
UPS Status device value incorrect in some cases
Running apcupsd 3.14.14 on two Windows boxes and one Rpi. When the UPS goes offline, the status device displays 'charging' (value 3) instead of 'offline' (value 0).
Also for a slave device, the status is always 'charging', no matter what.
Image 1: UPS2 (master) offline (USB disconnected)
Image 2: UPS3 (slave) when master offine
Image 3: UPS3 (slave) online, normal condition, 100% chargedTags: None
Leave a comment: