How do I setup my json to just use the cool setpoint for my three thermostats below within my json? reason for doing so is homebridge/Siri will only control one set point(my cool set point) so I figure if I link cool and heat set points to each other within homeseer than this should work however I don't know how to edit my json below to just use the cool set point. I tried posting this in the HomeKit thread but its not a very active and helpful thread as know one helps. Appreciate your help in advance.
My Json for thermostats is the following:
"type": "Thermostat",
"name": "Basement Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat62",
"ref": 65,
"stateRef": 68,
"controlRef": 68,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 71
},
{
"type": "Thermostat",
"name": "First Floor Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat36",
"ref": 39,
"stateRef": 42,
"controlRef": 42,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 45
},
{
"type": "Thermostat",
"name": "Second Floor Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat11",
"ref": 14,
"stateRef": 17,
"controlRef": 17,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 20
My Json for thermostats is the following:
"type": "Thermostat",
"name": "Basement Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat62",
"ref": 65,
"stateRef": 68,
"controlRef": 68,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 71
},
{
"type": "Thermostat",
"name": "First Floor Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat36",
"ref": 39,
"stateRef": 42,
"controlRef": 42,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 45
},
{
"type": "Thermostat",
"name": "Second Floor Thermostat",
"temperatureUnit": "F",
"setPointReadOnly": false,
"uuid_base": "Thermostat11",
"ref": 14,
"stateRef": 17,
"controlRef": 17,
"stateOffValues": [
0
],
"controlOffValue": 0,
"stateHeatValues": [
1
],
"controlHeatValue": 1,
"stateCoolValues": [
2
],
"controlCoolValue": 2,
"stateAutoValues": [
3
],
"controlAutoValue": 3,
"setPointRef": 20
Comment