Is a PlugIn needed for GoControl TBZ48?

[mriebese]

Setting up a new ZWave home with a GoControl TBZ48 thermostat using HS3
the stat shows up when adding it to the network but was wondering if you need to use a plug-in or will it work with the base application?

[Rupp]

It should work just fine with just HS3 and the Z-Wave plugin. You will want to create events to control the stat.

[kenm]

I have two of these and they work fine with the HS included Z-Wave plugin.

[mriebese]

Thanks Rupp been using HS for 20 + years and you've always been helpful! Getting a SmartStick+ is probably the way to go but not giving up on the Z-Troller just yet.
Strangely the Stat sets up fine in HS2 but not in HS3 using the same Z-Troller see the queries below

HS3:
Jul-29 9:08:44 AM Z-Wave 1 out of 1 Child devices of node 14 were created successfully.
Jul-29 9:08:43 AM Z-Wave Enabling auto send for thermostat status updates for device Node 14 Z-Wave Thermostat
Jul-29 9:08:42 AM Z-Wave Node 14 is Z-Wave version: Lib: 3.4 App: 1.2
Jul-29 9:08:41 AM Z-Wave Node: 14 Supports Class(es): SWITCH_BINARY, SWITCH_ALL, POWERLEVEL, CONFIGURATION, VERSION, MANUFACTURER_SPECIFIC_V2, NODE_NAMING
HS2:
7/29/2019 9:23:28 AM Z-Wave ********** Done with sync of Z-Wave Device with Node ID of 14
7/29/2019 9:23:12 AM Z-Wave Getting the current level for the node and any child devices...
7/29/2019 9:23:06 AM Z-Wave ========== Done with Z-Wave Device with Node ID of 14
7/29/2019 9:23:06 AM Z-Wave Device supports 3 groups for associations
7/29/2019 9:23:01 AM Z-Wave Z-Wave device 14 version: Lib: 3.40 App: 1.2
7/29/2019 9:23:00 AM Z-Wave Z-Wave manufacturer ID: 335=14FH (Error, Unknown), Type: 21570=5442H, ID: 21553=5431H
7/29/2019 9:22:59 AM Z-Wave Attempting to get manufacturer ID from device 14...
7/29/2019 9:22:59 AM Z-Wave Device: Z-Wave Interface Z-Wave Z-Wave Thermostat 14 (Node 14) supports class(es): COMMAND_CLASS_THERMOSTAT_MODE_V2, COMMAND_CLASS_THERMOSTAT_OPERATING_STATE, COMMAND_CLASS_THERMOSTAT_SETPOINT, COMMAND_CLASS_THERMOSTAT_FAN_MODE, COMMAND_CLASS_THERMOSTAT_FAN_STATE, COMMAND_CLASS_BATTERY, COMMAND_CLASS_CONFIGURATION_V2, COMMAND_CLASS_SENSOR_MULTILEVEL, COMMAND_CLASS_MULTI_CMD, COMMAND_CLASS_VERSION, COMMAND_CLASS_MANUFACTURER_SPECIFIC, COMMAND_CLASS_ASSOCIATION_V2, COMMAND_CLASS_SCENE_ACTUATOR_CONF, COMMAND_CLASS_SCENE_ACTIVATION, COMMAND_CLASS_POWERLEVEL, COMMAND_CLASS_CLOCK
7/29/2019 9:22:58 AM Z-Wave Contacting node 14 to get supported features
7/29/2019 9:22:57 AM Z-Wave ********** Reloading Z-Wave Device with Node ID of 14

[mriebese]

Just to follow up after optimizing the Zwave network and adding and removing the Stat again it has the correct classes on HS3 also setting parameter 23 to 8319 as describe in this thread has help with reporting status https://forums.homeseer.com/forum/th...erating-status