Announcement

Collapse
No announcement yet.

ZRC90-US Remote

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    ZRC90-US Remote

    Does anyone know if this remote will work with HS3? I got it to come in once but the buttons would not work. Tried exclude/include and it would not come in at all the second time. Reset it and tried again and still no go. Using L button to include as per the manual. R to remove. Thanks

    #2
    I have three of them and they're flawless. Press once for "A", press twice for "B" or whatever you want. I believe rprade had problems because he had too many devices or too many nodes. I have two z-nets with 48 nodes on one and about 20 on the other.

    Comment


      #3
      Originally posted by racerfern View Post
      I have three of them and they're flawless. Press once for "A", press twice for "B" or whatever you want. I believe rprade had problems because he had too many devices or too many nodes. I have two z-nets with 48 nodes on one and about 20 on the other.
      What buttons did you use to get it to work. I just included it and it shows 2 child devices. A battery one and a central scene. The central seen doesn't show any button presses after a button is pressed.

      Comment


        #4
        Here's three screenshots that should explain: The long list goes to 8003

        Note that the properties shown are by clicking on the Scene child not the root

        Click image for larger version

Name:	Screen Shot 03-02-20 at 04.45 PM.PNG
Views:	55
Size:	60.6 KB
ID:	1367659
        Click image for larger version

Name:	Screen Shot 03-02-20 at 04.47 PM.PNG
Views:	54
Size:	101.7 KB
ID:	1367660
        Click image for larger version

Name:	Screen Shot 03-02-20 at 04.48 PM.PNG
Views:	55
Size:	309.2 KB
ID:	1367661

        Comment


          #5
          racerfern Do you have to press a button and then while it is blinking press it again? In the youtube video Randy made he showed pressing a button and the LED blinks and while it is blinking he pressed the same button again and then it showed that button had been pressed. If you just press a button once and not during when the LED blinks it does not show a button press. This remote used to work when you pressed a button once and it showed a button press the first time. What happened?

          Comment


            #6
            I only press the button once, never had to press twice.

            I never had a problem with mine. In fact I shipped one of mine to rprade for testing. It ended up being his network having a lot of devices IIRC. I have two z-nets one with about 48 devices and the other with about 20. I've never had a problem. I think you NEED to stay below 50 devices.

            Comment


              #7
              Originally posted by racerfern View Post
              I think you NEED to stay below 50 devices.
              I just checked and I have 44 nodes. So I am not sure why it is not working as it did before. Thanks for the replies.

              Comment


                #8
                Check your log for z-wave errors of transmitting or receiving. I just checked, I have 47 devices on one and 21 on the other.

                Comment


                  #9
                  Originally posted by racerfern View Post
                  Check your log for z-wave errors of transmitting or receiving. I just checked, I have 47 devices on one and 21 on the other.
                  I haven't seen any errors. I am going to try it again and watch the logs. Did you have to set it as a secondary device first? I have tried to do a reset by holding down the R button until LED goes on and then off and then 3 quick presses of R. It seems to reset but after inclusion no button pushes are shown. Tried secure and non-secure.

                  EDIT: I just tried again. I did a reset on it first. I got the same results as I stated in post 5. Something might have changed in the driver, don't know. No errors in log.

                  Comment


                    #10
                    I'm pretty sure I just did a regular inclusion like any other device. After you reset it, pull the batteries, and when you go to include be very close to your controller. It has great range but I usually have battery operated devices very close to the controller when including.

                    You have a Smartstick, z-net or something else?

                    Comment


                      #11
                      This is with HS3 yes?

                      Comment


                        #12
                        Originally posted by racerfern View Post
                        This is with HS3 yes?
                        Yes I have HS3. I use the smartstick+. I have tried it at a few feet and right next to the stick. I have 2 of them so I did a reset on both. Included one got 2 child devices. Included the second and got 2 child devices as well. Neither one shows a button press.

                        Comment


                          #13
                          Do you have any other controller you can try? Smartthings?

                          rprade any thoughts or suggestions?

                          Comment


                            #14
                            Originally posted by racerfern View Post
                            Do you have any other controller you can try? Smartthings?

                            rprade any thoughts or suggestions?
                            I have a bunch of minimotes working great in HS3.

                            Comment

                            Working...
                            X