Announcement

Collapse
No announcement yet.

FGBS-222 Smart implant for doorbell settings for momentary switch

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #31
    If your doorbell is 12vdc the installation is simpler. You'll need a DPDT relay with a 12vdc coil. The relay you have has a 6vdc coil and is SPDT. Just insert the relay coil into the circuit in place of the bell, supply voltage to the bell through one set of Normally Open relay contacts and connect the other set of Normally Open contacts to IN1 and COM on the Implant.

    When you push the button the relay activates and one set of contacts rings the bell while the other set activates IN1 on the implant.

    Comment


      #32
      Originally posted by Alex_W View Post
      If your doorbell is 12vdc the installation is simpler. You'll need a DPDT relay with a 12vdc coil. The relay you have has a 6vdc coil and is SPDT. Just insert the relay coil into the circuit in place of the bell, supply voltage to the bell through one set of Normally Open relay contacts and connect the other set of Normally Open contacts to IN1 and COM on the Implant.

      When you push the button the relay activates and one set of contacts rings the bell while the other set activates IN1 on the implant.
      Thanks. 12v DPDT relay ordered

      Comment


        #33
        ‚ÄčI have my doorbell connected to the smart implant as mentioned in the previous posts here. Thinking I had it working after a while it seems that it is not working as intended. The big problem is that the Implant only updates ones after the doorbell has been pushed. See image (central scene).
        How can I also have the next one pushing the bell switch noticed and updated by the implant?

        Click image for larger version  Name:	Schermafbeelding 2021-11-08 om 14.16.19.png Views:	0 Size:	203.2 KB ID:	1506977

        and created an event. Or should I use Key held down?
        Attached Files

        Comment


          #34
          After updating Hs3 to the latest version and having the updated z-wave core plugin installed I now have all 17 devices. After fiddling around with the device settings (parameter 20=2 and parameter 40=1 it seems to work now. First had parameter 40=8 but that resulted in getting an update every minute or so, triggering the event continuously.

          Click image for larger version

Name:	Schermafbeelding 2021-11-09 om 11.58.30.png
Views:	61
Size:	142.1 KB
ID:	1507143
          Click image for larger version

Name:	Schermafbeelding 2021-11-09 om 13.00.54.png
Views:	51
Size:	270.7 KB
ID:	1507144

          Comment


            #35
            This is driving me ... After thinking it worked. It is not. Is anyone using this device for the same purpose and has it working? Maybe willing to share the right settings? I first thought the device needed a reset after the bell-button was pressed (switch 5 stayed on). That did not help much. After the initial time the bell was pressed, nothing is triggered again. So some of the setting stays in its pressed state and never gets renewed - refreshed/ or returns to its initial state. So how to get this going the right way?

            Click image for larger version

Name:	Schermafbeelding 2021-11-24 om 11.52.01.png
Views:	37
Size:	198.2 KB
ID:	1509777

            Comment


              #36
              Any thoughts / advise on this?

              Comment


                #37
                Still did not solve this. After one time pushing the doorbell button it stays at the one received update and no new update is registered. So what parameter to use to get update every-time the button has been pushed? I tried to have a reset or so on the button (switch) part of the devices listed but that did not help me.
                This is the manual https://manuals.fibaro.com/content/m...-EN-T-v1.0.pdf
                Would be nice if someone can help me out with this...

                Comment

                Working...
                X