Announcement

Collapse
No announcement yet.

Z-Wave Leak Sensor

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ts1234
    replied
    Just be sure you are not trying to use S2 security. They'll work for a bit and then go away...all kinds of flakey things. Even support will tell you that's beta and not to do it. The HS Leak sensors were really not happy with S2, though other devices are flakey too. I had to rebuild my whole install because I started over clean adding everything with S2. There is no course back other than deleting and adding back w/out S2. If by chance this is your issue...make sure you delete them from the system at the interface level and then factory reset each of them before trying to add back.

    Leave a comment:


  • markc
    replied
    I tried numerous things with no luck until I powered off the server running my HS4 instance and powered it back on again. That worked and I was able to successfully continue adding Z-Wave devices. I am running HS4 on Ubuntu with a HomeSeer ZWave stick. Playing with settings inside HS4 didn’t help. Neither did rebooting the virtual machine that HS4 is running in. Nor did removing and reinserting the ZWave stick. Fortunately a full power down and restart did the trick.

    Leave a comment:


  • markc
    replied
    I just got the same error with 2 different devices (a Jasco switch and a Dome mouse trap). I previously added a bunch of sensors as I migrate my devices from SmartThings to HomeSeer.

    Leave a comment:


  • ts1234
    replied
    I have 8 HS Leak sensors. When Gen 7 hits I will buy more. They all work fine. I added w/ HS3, but updated to HS4 and all good still.

    One thing I do know...is under HS3 when using the beta z-wave driver supporting S2 they were pretty much paper weights.

    Leave a comment:


  • ezmaass
    replied
    I have multiple Dome leak sensors included in my HS4 environment using the Z-stick - all have added with no problems. I would try excluding it first and trying again. The only device that I've had fail (and eventually gave up on) was a Zooz light switch.

    Leave a comment:


  • Charles_cz
    replied
    I use those with no issues.

    Leave a comment:


  • gelessor
    replied
    It’s the one From HomeSeer.

    Use a z-stick b haven’t had problems with any other devices. I had hoped to by 4 or 5 of these.. but it looks Ike they’re not going to work fo m.

    Leave a comment:


  • Charles_cz
    replied
    What Leak sensor are you trying to include?

    Do you have another z-wave interface you could use as secondary? I remember one time I was having issues with including new devices once I reached certain number of nodes. It was not near the limit but I was having hard time including additional devices. I don't remember if it was at the end failing z-stick or something else.

    If you have another z-stick or something you could create second network and see if it will get included on new network. It would be good next step to troubleshoot. It never huts to have spare replacement for you existing z-wave interface just in case the one you have fails.

    Leave a comment:


  • gelessor
    replied
    Thanks for the tips. Unfortunately non have changed the results. I am still unable to add the device user either the secure or non-secure methods.

    could this be a bug in HS4 or the plug-in?

    All other z-wave devices, including door locks, were discovered without a problem.



    Leave a comment:


  • Charles_cz
    replied
    gelessor Try exclude the sensor first. This sometimes happen when device has been previously included. It always good idea when you have similar problems to exclude first and reset the device as well.

    Leave a comment:


  • mulu
    replied
    Did you try to add it as a not secure node? I just got a similar but not exactly the same error. After switching to adding it non-secure the error disappeared (but it still failed at the end which might be another issue).

    Leave a comment:


  • gelessor
    started a topic Z-Wave Leak Sensor

    Z-Wave Leak Sensor

    I am unable to add a new sensor. I have tried secure and non-secure add modes.

    Getting the error. "Error. the Add Node response object is null and a normal ending was not reported"

    I also tried resetting the sensor but getting the same errors.

    Any thoughts?

    Thanks
Working...
X