Hey, All,
I moved my HS3 system to RPi early in 2020. I have purchased HS4 but not implemented it yet, and I'm thinking I will probably move the system back to Windows when I do. One main reason it that the RPi version seems to be somewhat flakey. For example, (and this is not the first time something similar has happened),I came home today from a couple hours of errands to find 5 or 6 lights on in the middle of broad daylight. They were both outside lights that shouldn't be on, and a couple of inside lights too, and interestingly they were some on both the X-10 and Z-wave interfaces. It doesn't help that this happened about 10 minutes after I left, and the wife witnessed all this happening without her tripping any of them. (Way bad for already low WAF anyway, lol)
Below is the HS3 log, and I honestly don't know enough about the system to understand what it means that something was triggered by/from the CAPI Control Handler. Further, I noticed that whatever went haywire at 2:46PM, it is bracketed by HSBuddy cleanup actvities. Could HSBuddy have caused it? Any other ideas what there's a Ghost in the Machine?? I see all the X-10 errors. My interface is a CM11A plugged into Jeff Volp's excellent XTB-IIR. My Z-wave interface is a good ol' HomeSeer stick.
Thanks in advance for any insights. Much appreciated,
Mike
I moved my HS3 system to RPi early in 2020. I have purchased HS4 but not implemented it yet, and I'm thinking I will probably move the system back to Windows when I do. One main reason it that the RPi version seems to be somewhat flakey. For example, (and this is not the first time something similar has happened),I came home today from a couple hours of errands to find 5 or 6 lights on in the middle of broad daylight. They were both outside lights that shouldn't be on, and a couple of inside lights too, and interestingly they were some on both the X-10 and Z-wave interfaces. It doesn't help that this happened about 10 minutes after I left, and the wife witnessed all this happening without her tripping any of them. (Way bad for already low WAF anyway, lol)
Below is the HS3 log, and I honestly don't know enough about the system to understand what it means that something was triggered by/from the CAPI Control Handler. Further, I noticed that whatever went haywire at 2:46PM, it is bracketed by HSBuddy cleanup actvities. Could HSBuddy have caused it? Any other ideas what there's a Ghost in the Machine?? I see all the X-10 errors. My interface is a CM11A plugged into Jeff Volp's excellent XTB-IIR. My Z-wave interface is a good ol' HomeSeer stick.
Thanks in advance for any insights. Much appreciated,
Mike
Apr-03 2:59:52 PM | HSBuddy | Cleanup thread removed 190 entries from device history. |
Apr-03 2:59:32 PM | Z-Wave Warning | Exception processing received application frame for encapsulation: Index was outside the bounds of the array. |
Apr-03 2:56:23 PM | Z-Wave Warning | Exception processing received application frame for encapsulation: Index was outside the bounds of the array. |
Apr-03 2:52:42 PM | Z-Wave | Device: Outdoor Garage 2 Opener Set to OFF |
Apr-03 2:47:18 PM | Z-Wave | Device: Basement Living Luminance Set to 67.07 (%) |
Apr-03 2:47:18 PM | Z-Wave | Device: Basement Living Relative Humidity Set to 40.61 (%) |
Apr-03 2:47:18 PM | Z-Wave | Device: Basement Living Temperature Set to 65.21 (F) |
Apr-03 2:47:01 PM | Z-Wave | Device: Main Living Floor Lamp Set to ON |
Apr-03 2:47:01 PM | Z-Wave | Device: Main Living Floor Lamp Set to OFF |
Apr-03 2:47:01 PM | Device Control | Device: Main Living Floor Lamp to On (255) by/from: CAPI Control Handler |
Apr-03 2:46:59 PM | Z-Wave | Device: Basement Living Light Set to 99 |
Apr-03 2:46:59 PM | X10 WARNING | 3.939 seconds for CM11A to send data. Possible noise or interference on power line. |
Apr-03 2:46:58 PM | X10 WARNING | Still waiting for CM11a to send data... (3.028 sec) |
Apr-03 2:46:57 PM | X10 WARNING | Still waiting for CM11a to send data... (2.023 sec) |
Apr-03 2:46:56 PM | Device Control | Device: Main Master Bath Garden Tub Overhead to On (100) by/from: CAPI Control Handler |
Apr-03 2:46:56 PM | X10 WARNING | Still waiting for CM11a to send data... (1.004 sec) |
Apr-03 2:46:54 PM | X10 WARNING | 4.129 seconds for CM11A to send data. Possible noise or interference on power line. |
Apr-03 2:46:54 PM | X10 WARNING | Still waiting for CM11a to send data... (4.064 sec) |
Apr-03 2:46:53 PM | X10 WARNING | Still waiting for CM11a to send data... (3.045 sec) |
Apr-03 2:46:52 PM | X10 WARNING | Still waiting for CM11a to send data... (2.021 sec) |
Apr-03 2:46:51 PM | X10 WARNING | Still waiting for CM11a to send data... (1.002 sec) |
Apr-03 2:46:51 PM | Device Control | Device: Main Entry Front Porch Overhead to On (100) by/from: CAPI Control Handler |
Apr-03 2:46:50 PM | X10 WARNING | 3.937 seconds for CM11A to send data. Possible noise or interference on power line. |
Apr-03 2:46:49 PM | X10 WARNING | Still waiting for CM11a to send data... (3.04 sec) |
Apr-03 2:46:48 PM | X10 WARNING | Still waiting for CM11a to send data... (2.025 sec) |
Apr-03 2:46:47 PM | X10 WARNING | Still waiting for CM11a to send data... (1.004 sec) |
Apr-03 2:46:46 PM | Device Control | Device: Basement Living Light to On (99) by/from: CAPI Control Handler |
Apr-03 2:46:45 PM | X10 WARNING | 4.122 seconds for CM11A to send data. Possible noise or interference on power line. |
Apr-03 2:46:45 PM | X10 WARNING | Still waiting for CM11a to send data... (4.057 sec) |
Apr-03 2:46:44 PM | X10 WARNING | Still waiting for CM11a to send data... (3.043 sec) |
Apr-03 2:46:43 PM | X10 WARNING | Still waiting for CM11a to send data... (2.021 sec) |
Apr-03 2:46:42 PM | X10 WARNING | Still waiting for CM11a to send data... (1.002 sec) |
Apr-03 2:46:41 PM | Z-Wave | Device: Outdoor Garage 1 G1 Sconces Set to 255 |
Apr-03 2:46:41 PM | Device Control | Device: Outdoor Entry Front Walkway Lamps to On (100) by/from: CAPI Control Handler |
Apr-03 2:46:41 PM | Device Control | Device: Main Master Bath Garden Tub Overhead to Brightness 5% (5) by/from: CAPI Control Handler |
Apr-03 2:46:41 PM | Z-Wave | Device: Basement Living Light Set to 5 |
Apr-03 2:46:41 PM | Device Control | Device: Main Entry Front Porch Overhead to Brightness 5% (5) by/from: CAPI Control Handler |
Apr-03 2:46:41 PM | Device Control | Device: Outdoor Garage 1 G1 Sconces to On (255) by/from: CAPI Control Handler |
Apr-03 2:46:41 PM | Device Control | Device: Basement Living Light to 5% (5) by/from: CAPI Control Handler |
Apr-03 2:46:40 PM | Device Control | Device: Outdoor Garage 2 Outside Sconces to On (255) by/from: CAPI Control Handler |
Apr-03 2:44:52 PM | HSBuddy | Cleanup thread removed 244 entries from device history. |
Apr-03 2:36:40 PM | Z-Wave | Device: Outdoor Garage 2 Meter Pulse Set to Pulse Count of 35 |
Apr-03 2:36:15 PM | Error | Problem serializing data for JSON request: Object reference not set to an instance of an object. |
Comment