Announcement

Collapse
No announcement yet.

Fibaro water sensor spontaneously throwing an error for one of it's child devices

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Fibaro water sensor spontaneously throwing an error for one of it's child devices

    So one of my water sensors has spontaneously throwing an error that it received data from Node 39/2 but there is no corresponding device. (39 is the z-wave id of this particular sensor). For fun I tried re-scanning it and got the following results:

    Code:
    Time
    From
    Type
    Message
    
    
    1/4/2022 12:38:17 PM
    Legacy-Plugin
    Z-Wave Error
    (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found.(2) Node/Instance=39/2
    
    1/4/2022 12:38:17 PM
    Legacy-Plugin
    Z-Wave Error
    (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found.(2) Node/Instance=39/2
    
    1/4/2022 12:36:15 PM
    Legacy-Plugin
    Z-Wave
    Device: Basement Office Office Overhead Light kW Hours Set to 145.535 (145.535 kW Hours)
    
    1/4/2022 12:34:25 PM
    Legacy-Plugin
    Z-Wave
    Device: Main Floor Kitchen Flood Sensor Kitchen Temperature 2 Set to 30.6 (C)
    
    1/4/2022 12:34:22 PM
    Legacy-Plugin
    Z-Wave
    5 out of 5 Child devices of node 39 were created successfully.
    
    1/4/2022 12:34:21 PM
    Legacy-Plugin
    Z-Wave
    Setting wake-up interval for device Basement Furnace Room Flood Sensor 1 Root to 12 hours and 0 minutes.
    
    1/4/2022 12:34:21 PM
    Legacy-Plugin
    Z-Wave
    Programming device Basement Furnace Room Flood Sensor 1 Root (39) to send wake-up notifications to HomeSeer.
    
    1/4/2022 12:34:21 PM
    Legacy-Plugin
    Z-Wave
    Setting wake-up interval for device Basement Furnace Room Flood Sensor 1 Root to 12 hours and 0 minutes.
    
    1/4/2022 12:34:20 PM
    Legacy-Plugin
    Z-Wave
    Getting association information for Basement Furnace Room Flood Sensor 1 Root
    
    1/4/2022 12:34:20 PM
    Legacy-Plugin
    Z-Wave
    Assigning return route from node 1 to Basement Furnace Room Flood Sensor 1 Root
    
    1/4/2022 12:34:20 PM
    Legacy-Plugin
    Z-Wave
    Zoe: Adding association for Z-Wave device Basement Furnace Room Flood Sensor 1 Root (Node 39, Group 2, Endpoint 2) to HomeSeer
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Assigning return route from node 1 to Basement Furnace Room Flood Sensor 1 Root
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Zoe: Adding association for Z-Wave device Basement Furnace Room Flood Sensor 1 Root (Node 39, Group 1, Endpoint 1) to HomeSeer
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    All associations for node 39 have been retrieved successfully, it supports associations on these groups: 1, 2, 3.
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Node 39 Association Group 3 can have 1 associations, and currently has 1
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Node 39 Association Group 2 can have 5 associations, and currently has 1
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Node 39 Association Group 1 can have 5 associations, and currently has 1
    
    1/4/2022 12:34:19 PM
    Legacy-Plugin
    Z-Wave
    Getting association information for node 39
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave
    Alarm Sensor Node 39 Supports 2 Alarm Types: GENERAL_PURPOSE_ALARM WATER_LEAK_ALARM
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave Error
    (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found.(2) Node/Instance=39/2
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave Error
    (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found.(2) Node/Instance=39/2
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave Warning
    Node 39, EndPoint=2 Multilevel Sensor Report was not received (B) - the child device will NOT be configured properly.
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave
    Processing Information for Node 39 Multi-CHANNEL Command Class of SENSOR_MULTILEVEL_V8, Endpoint 2
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave
    Processing Information for Node 39 Multi-CHANNEL Command Class of SENSOR_BINARY, Endpoint 1
    
    1/4/2022 12:34:18 PM
    Legacy-Plugin
    Z-Wave
    Node 39 is Z-Wave version: Lib: 3.67 App: 25.25
    
    1/4/2022 12:34:17 PM
    Legacy-Plugin
    Z-Wave
    Node: 39 Supports Class(es): SENSOR_BINARY, SENSOR_ALARM, MULTI_CHANNEL_V3, ASSOCIATION, MULTI_INSTANCE_ASSOCIATION, MANUFACTURER_SPECIFIC_V2, CONFIGURATION, VERSION, BATTERY, WAKE_UP
    
    1/4/2022 12:34:17 PM
    Legacy-Plugin
    Z-Wave
    Syncing Z-Wave nodes with device list...
    
    1/4/2022 12:34:17 PM
    Legacy-Plugin
    Z-Wave
    Found 61 Z-Wave nodes
    
    1/4/2022 12:34:17 PM
    Legacy-Plugin
    Z-Wave
    Getting Z-Wave node list for network DB46E657...
    The rescan took place, but did say that for "Endpoint 2" a configuration was not received and will not be configured properly. I guess I could remove and re-add the device, but I really don't want to if I don't need to, so I don't have to go back and fix all my events that touch it, too. Any ideas?

    regards,

    Paul


Working...
X