Announcement

Collapse
No announcement yet.

Jasco GE Enbrighten Motion Switch - Need Motion Status Parameters - Solved!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • JRose
    replied
    I ended up having to re-image my system due to a static IP problem. After the image, I updated HS and the Z-Wave plugin to the most recent versions. I couldn't do a restore, so I recreated the HS devices using the Z-wave interface function. To my surprise, it re-created correctly. Some of the other devices did not re-create properly but I can fix them. It's a new home so there are not a lot of items set up yet.


    FYI - system is still being rebuilt but here is the current data.

    Date/time=9/16/2022 7:31:06 PM EDT
    Version=HomeSeer HS4 Pi Hub G3 Edition 4.2.16.0 (Linux)
    MONO Version=Mono JIT compiler version 6.12.0.122 (tarball Mon Feb 22 17:40:01 UTC 2021)

    License=Registered
    Confguration File=/usr/local/HomeSeer/Data/HomeSeerData.json
    Uptime=0 Days 1 Hour 22 Minutes 22 Seconds
    Lan IP=127.0.0.1 (HTPiHubG3v2)
    Device Count=15
    Event Count=0
    Plugins Enabled=Z-Wave:
    Modules/Threads=87 Modules, 48 Threads
    Available Threads=399
    HomeSeer Memory Used=98 Mbytes
    Plugins Installed=Big6 3.44.0.0,BLLAN 2.0.45.0,EnvisaLinkAdemco 3.0.0.31,HS MyQ 4.0.9.0,mcsMQTT 5.26.5.4,Z-Wave 4.0.3.0
    Disk Size=28.33GB

    Leave a comment:


  • jgreenberg01
    replied
    Originally posted by Rupp View Post

    What version of the Z-Wave plugin are/were you using when adding this device?
    I was using 3.0.10.0 at the time.

    Updated to 4.0.3.0 later, but it caused a bunch of issues, so I rolled back.

    Leave a comment:


  • johnpeterson
    replied
    I'm using Zwave 3.0.10.0 on HS 4.2.14.0


    Sent from my iPhone using Tapatalk

    Leave a comment:


  • Rupp
    replied
    Originally posted by jgreenberg01 View Post
    FWIW, I have 2 of these switches and they included properly:
    Click image for larger version

Name:	Enbrighten Motion Sensor.png
Views:	75
Size:	33.7 KB
ID:	1566351
    They both work as expected with no errors in the log.

    I see you tried more than once, but maybe try one more time non-secure just to see if the errors go away.
    What version of the Z-Wave plugin are/were you using when adding this device?

    Leave a comment:


  • JRose
    replied
    Originally posted by TC1 View Post
    Since this is a fairly new device on the market, you should open a ticket with HS Support. More than likely, they need to modify the Z-wave plugin to properly support all the features of the device.
    Yes, I have a Ticket Open and will report back here any updates.
    They asked me to move the hometroller Pi closer and try again. I pulled it out of my closet and placed it next to the switch - no better. More to come.

    Leave a comment:


  • johnpeterson
    replied
    I have 2 of these switches and one included correctly and the other has the same issue as you report. Both have the same product id and same firmware version.
    Manufacturer:
    Jasco Products
    Type:
    0x494D
    ID:
    0x3032
    Listens:
    Yes
    Version: 4.54 (Unknown) Firmware: 5.39 Hardware: 255
    For the bad switch I receive the same error message you get and my status/graphics are the same as your screenshot above.

    For the good switch I receive no error messages (works great) and my status/graphics page is below. I changed the bad switch status/graphics to match the one below and still get the same error. I haven't opened a ticket yet or had much chance to investigate further but plan to soon.

    Click image for larger version

Name:	jasco1.jpg
Views:	53
Size:	58.1 KB
ID:	1566393
    Attached Files

    Leave a comment:


  • jgreenberg01
    replied
    FWIW, I have 2 of these switches and they included properly:
    Click image for larger version

Name:	Enbrighten Motion Sensor.png
Views:	75
Size:	33.7 KB
ID:	1566351
    They both work as expected with no errors in the log.

    I see you tried more than once, but maybe try one more time non-secure just to see if the errors go away.

    Leave a comment:


  • TC1
    replied
    Since this is a fairly new device on the market, you should open a ticket with HS Support. More than likely, they need to modify the Z-wave plugin to properly support all the features of the device.

    Leave a comment:


  • Jasco GE Enbrighten Motion Switch - Need Motion Status Parameters - Solved!


    After including a (Jasco) GE Enbrighten Smart Motion Switch, I get a root device with 2 features created. One is the switch which works correctly and the other is "Notification" which I am assuming is the motion sensor but it doesn't appear to be created correctly. I have excluded / included a couple of times and re-scanned but no luck. The log looks normal EXCEPT for this error during creation

    9/14/2022 6:43:24 PM
    Legacy-Plugin
    Z-Wave Warning
    Node 5 did not respond to the Notification Supported request.

    And this error when moving in front of the sensor.

    9/14/2022 6:54:12 PM
    Legacy-Plugin
    Z-Wave Error
    Notification Report from node 5 for type Home Security received, but the corresponding device Node ID cannot be found. (2, Type=7)

    I've uploaded my pictures of the device page and the feature page. Does anyone have one that was created successfully and can provide the correct Status/Graphics parameters

    Thanks
    Jeff
    Attached Files
Working...
X