After seeing the announcement that there's now a plugin for the CM15A, I ordered one. It came today, and I installed it and the plugin, but I can't seem to make it do anything. I can't send an X10 command successfully to my "Chime" from within Homeseer. And Homeseer doesn't seem to respond to a press of my X10 fob. However, if I set my keyfob to the Chime's address, it chimes when I press the keyfob, so I guess the CM15A itself must be working.
I tried this both before and after installing the software that came with the CM15A plugin, thinking this might make a difference, but it didn't.
I figure I'm missing something obvious, but I don't know what (obviously)
I have X10 disabled on my Insteon PLM, and enable on the CM15A plugin. When I press "Config" for the Plugin, I get an error message saying "There is no configuration for this plugin."
The log seems to show everything being started OK on startup:
8/20/2008 9:35:06 PM CM15A Initialization Successful.
8/20/2008 9:35:05 PM Info Initializing Plug-in: X10 CM15A
8/20/2008 9:35:05 PM Info Initializing X10 Plug-in: X10 CM15A On COM Port 2
8/20/2008 9:35:05 PM Startup Initializing Plug-Ins
8/20/2008 9:35:05 PM Info This Z-Wave PC controller is type: ZW_LIB_INSTALLER
8/20/2008 9:35:05 PM Z-Wave Controller firmware version: 1.12
8/20/2008 9:35:05 PM Info Z-Wave interface node ID: 1
8/20/2008 9:35:05 PM Info Z-Wave interface version: 4
8/20/2008 9:35:05 PM Info Found 1 Z-Wave nodes
8/20/2008 9:35:05 PM Startup Initializing Z-Wave Interface on COM port: 3 at 115K baud.
8/20/2008 9:35:05 PM Startup Restoring device status
8/20/2008 9:35:05 PM Info Found plug-in: Smarthome SwitchLinc, version: 1.0.0.6
8/20/2008 9:35:05 PM Info Found plug-in: Insteon, version: 1.1.50.38463
8/20/2008 9:35:05 PM Info Found plug-in: X10 CM15A, version: 1.0.0.0
I tried this both before and after installing the software that came with the CM15A plugin, thinking this might make a difference, but it didn't.
I figure I'm missing something obvious, but I don't know what (obviously)
I have X10 disabled on my Insteon PLM, and enable on the CM15A plugin. When I press "Config" for the Plugin, I get an error message saying "There is no configuration for this plugin."
The log seems to show everything being started OK on startup:
8/20/2008 9:35:06 PM CM15A Initialization Successful.
8/20/2008 9:35:05 PM Info Initializing Plug-in: X10 CM15A
8/20/2008 9:35:05 PM Info Initializing X10 Plug-in: X10 CM15A On COM Port 2
8/20/2008 9:35:05 PM Startup Initializing Plug-Ins
8/20/2008 9:35:05 PM Info This Z-Wave PC controller is type: ZW_LIB_INSTALLER
8/20/2008 9:35:05 PM Z-Wave Controller firmware version: 1.12
8/20/2008 9:35:05 PM Info Z-Wave interface node ID: 1
8/20/2008 9:35:05 PM Info Z-Wave interface version: 4
8/20/2008 9:35:05 PM Info Found 1 Z-Wave nodes
8/20/2008 9:35:05 PM Startup Initializing Z-Wave Interface on COM port: 3 at 115K baud.
8/20/2008 9:35:05 PM Startup Restoring device status
8/20/2008 9:35:05 PM Info Found plug-in: Smarthome SwitchLinc, version: 1.0.0.6
8/20/2008 9:35:05 PM Info Found plug-in: Insteon, version: 1.1.50.38463
8/20/2008 9:35:05 PM Info Found plug-in: X10 CM15A, version: 1.0.0.0
Comment