Announcement

Collapse
No announcement yet.

IGNORE this, device status, ? if working?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    IGNORE this, device status, ? if working?

    IGNORE this thread, I got it to work, i reset it again, repositioned it,now works.
    I could not figure out how to delete this message
    thanks
    nick



    Help, not sure if device working, or just not enough nodes?
    device 2, dimmable light. device 5, dimmable light
    device 4, thermostat wayne dalton
    USB zstick as primary controller, and homeseer basic software
    (and also ztools, just reset device and restored it)

    polling returns "unknwn" for device 5
    device 5 is in basement, but directly below the thermostat (only about 8 feet)
    not getting good control of device 5

    any help to optimize this is appreciated.
    I've done optimize, rescan, poll, etc

    thanks
    Nick




    5/24/2009 7:25:04 PM - Z-Wave - ---------------------------------------------------------------------------------
    5/24/2009 7:25:04 PM - Z-Wave - ********** Reloading Z-Wave Device with Node ID of 5 **********
    5/24/2009 7:25:04 PM - Z-Wave - Contacting node 5 to get supported features
    5/24/2009 7:25:05 PM - Z-Wave - Device: Z-Wave Interface Dimmable Device 5 (Node 5) supports class(es): COMMAND_CLASS_BASIC, COMMAND_CLASS_SWITCH_MULTILEVEL, COMMAND_CLASS_SWITCH_ALL, COMMAND_CLASS_VERSION, COMMAND_CLASS_MANUFACTURER_SPECIFIC
    5/24/2009 7:25:05 PM - Z-Wave - Attempting to get manufacturer ID from device 5...
    5/24/2009 7:25:26 PM - Z-Wave - No version information available for device.
    5/24/2009 7:25:26 PM - Z-Wave - ========== Done with Z-Wave Device with Node ID of 5 ==========
    5/24/2009 7:25:26 PM - Database Item - Saving Device Dimmable Device 5
    5/24/2009 7:25:26 PM - Z-Wave - ********** Done with sync of Z-Wave Device with Node ID of 5 **********
    5/24/2009 7:25:46 PM - Z-Wave - ---------------------------------------------------------------------------------
    5/24/2009 7:25:46 PM - Z-Wave - ********** Reloading Z-Wave Device with Node ID of 2 **********
    5/24/2009 7:25:46 PM - Z-Wave - Contacting node 2 to get supported features
    5/24/2009 7:25:47 PM - Z-Wave - Device: Z-Wave Interface Dimmable Device 2 (Node 2) supports class(es): COMMAND_CLASS_BASIC, COMMAND_CLASS_SWITCH_MULTILEVEL, COMMAND_CLASS_SWITCH_ALL, COMMAND_CLASS_VERSION, COMMAND_CLASS_MANUFACTURER_SPECIFIC
    5/24/2009 7:25:47 PM - Z-Wave - Attempting to get manufacturer ID from device 2...
    5/24/2009 7:25:48 PM - Z-Wave - Z-Wave manufacturer ID: 5=5H (Intermatic), Type: 3=3H, ID: 3=3H
    5/24/2009 7:25:49 PM - Z-Wave - Z-Wave device 2 version: Lib: 1.28 App: 1.0
    5/24/2009 7:25:49 PM - Z-Wave - ========== Done with Z-Wave Device with Node ID of 2 ==========
    5/24/2009 7:25:49 PM - Database Item - Saving Device Dimmable Device 2
    5/24/2009 7:25:49 PM - Z-Wave - ********** Done with sync of Z-Wave Device with Node ID of 2 **********
    Last edited by aoz; May 24, 2009, 06:56 PM.
Working...
X