CT30 and Celsius

[ceesmf]

Strangly, after a few resets, suddenly it's possible to set the cool and heat setpoints on HS touch albeit indeed only at in/decrements of 1 degree.
but there are a few other bugs:
1) manual changes on the ct30 itself are not reported back to homeseer i.e. they are not synchronized.
2)after a reset/restart of homeseer the cool setpoint is always set to 0 degrees i.e. it is not read back from the CT30 correctly
3) the min/max for F/C table in the thermostat.ini is not taken in account, ie it only looks at the F value,only after changing this table it is possible to script values below 40 degrees (essential if you don't want to be cooked ;-) )
(what is the use of this table anyway ?)
4) In HStouch Designer , setting the setpoint with a button is still only possible with the min/max values for Fahrenheit , not the "new" min/max values for Celcius
edit 2) solved , after changing the min / max values for Fahrenheit in "logical values" voor Celcius, both setpoints, cool and heat , can be set and are displayed correctly
@Paul, this should solve your problem too

[paul]

I just realized I should clarify - when I refer to not being able to change the setpoint in HS Touch, I'm referring to the Climate page on my iPhone HS Touch. I don't know if it works on other devices...

Paul

[ceesmf]

Can confirm the above

[paul]

Hi Rich,

Ok, that *partially* worked. Now all the numbers display in celsius. There's a new bug now, and one possible tweak (?)

The bug: In HS Touch, the Climate control page now correctly shows Celsius, but when I try to change the setpoint it no longer works. I can hit the up/down arrows all I want, but the set point doesn't change. (It worked when it was showing in F). In the Web browser interface, I can change the set point, and it correctly shows in C.

The tweak: The thermostat allows us to change the setpoint in 0.5 degree increments, as 1 degree C is indeed a wider number than 1 degree F. On the Thermostat device it shows the current temp to 1 decimal place, and in the Web browser where you change the setpoint it shows the current temp with 1 decimal place. However, the web page only lets me change the setpoint in full degree increments, even if I specify the half degree. Additionally, in the Climate control page on HS Touch it only displays the temp to zero decimal places, and I suspect I'll only be able to change it in full degree increments there). Any chance of tweaking it to display and allow the changing in half degree increments everywhere?

Many thanks!

Paul

[rjh]

Ok, run this updater and it should display all readings in Celsius as long as you have Celsius enabled on the general tab in setup:

ftp://ftp.homeseer.com/pub/HomeSeerU...RO2_5_0_28.exe

Ah, sorry - 2.5.0.23, HSPRO on my own server. Many thanks!

[paul]

Ah, sorry - 2.5.0.23, HSPRO on my own server. Many thanks!

[rjh]

I can post an updater for you, but I need to know if you are using HS2, HSPRO, or a HomeTroller.

I'm using 2.5.0.23.

[paul]

I'm using 2.5.0.23.

[rjh]

I have a fix, what edition of HomeSeer are you using?

[ceesmf]

Celsius

Same problem here

[FernandoSolanes]

Nope no solution as of yet, I have a pending support ticket but still the same bug

[paul]

Did you ever find an answer for this? Just setup my CT30.

Homeseer -> Set to Celsius
Thermostat -> Set to Celsius
Z-Wave Thermostat Temperature -> Displays in Celsius
Z-Wave Thermostat -> Displays in Fahrenheit
Z-Wave Setpoint controls, etc -> Displays in Fahrenheit

Paul

[Rupp]

If you are within your 30 days free support then put in a help desk ticket on this issue using the blue support link above.

[FernandoSolanes]

Professional Edition 2.5.0.23

[Rupp]

What version of HomeSeer are you running?