Kwickset Lock Zwave Add Problem

[jpm4000]

I am using a Ztroller (Newly purchased) and a Kwickset Deadbolt Zwave Lock.

I use the Add function on the ZTroller. Then I connect the Ztroller to the HomeTroller and click "Import Devices" in the Interface Dialog for the Zwave interface.

The log shows the following errors:

2/11/2013 9:01:40 PM Z-Wave **********
2/11/2013 9:01:40 PM Z-Wave ********** Adding Z-Wave Device with Node ID of 3 Type GENERIC_TYPE_ENTRY_CONTROL=40H **********
2/11/2013 9:01:40 PM Z-Wave **********
2/11/2013 9:01:40 PM Z-Wave Contacting node 3 to get supported features
2/11/2013 9:01:41 PM Z-Wave Negotiating SECURITY SCHEME for (3)
2/11/2013 9:01:51 PM Error Z-Wave was unable to negotiate a compatible security scheme with node 3
2/11/2013 9:01:51 PM Z-Wave Failed to get SECURITY SCHEME from node 3. Device may not be added properly to HomeSeer.
2/11/2013 9:01:51 PM Z-Wave The security device may have a timeout when adding to the network, bring the device close to HomeSeer and use the Add Node button to add it (remove it first)2/11/2013 9:01:51 PM Z-Wave Warning Failed to add new SECURE node 3 to the network securely - device will not operate properly.
2/11/2013 9:01:51 PM Z-Wave Device: Z-Wave Z-Wave Interface (Node 3) supports class(es): COMMAND_CLASS_MANUFACTURER_SPECIFIC, COMMAND_CLASS_VERSION, COMMAND_CLASS_SECURITY
2/11/2013 9:01:51 PM Z-Wave Attempting to get manufacturer ID from device 3...2/11/2013 9:01:52 PM Z-Wave Z-Wave manufacturer ID: 144=90H (Kwikset), Type: 1=1H, ID: 1=1H2/11/2013 9:01:53 PM Z-Wave Z-Wave device 3 version: Lib: 3.28 App: 2.62/11/2013 9:01:53 PM Z-Wave ********** Done with Z-Wave Device with Node ID of 3 **********

After this, only a generic "on/off" device is added to the devices page. Type Z Wave Lock. But the lock cannot be controlled from HS software. Attempts to communicate with lock using rescan result in the following errors:

2/11/2013 9:08:52 PM Z-Wave ---------------------------------------------------------------------------------2/11/2013 9:08:52 PM Z-Wave ********** Reloading Z-Wave Device with Node ID of 3 **********2/11/2013 9:08:52 PM Z-Wave Getting SECURITY class information for Z-Wave Z-Wave Interface (3)2/11/2013 9:09:03 PM Z-Wave Failed (A) to get SECURE command classes from node 3. Device may not be added properly to HomeSeer.2/11/2013 9:09:03 PM Z-Wave Warning: Could not get SECURE command classes for node 3, Z-Wave Z-Wave Interface . Cannot continue.2/11/2013 9:09:03 PM Z-Wave ========== Done with Z-Wave Device with Node ID of 3 ==========

Can anyone tell me what boneheaded mistake I've made?
I have tried removing and readding the lock, but no changes.

Thanks.

[Rupp]

To add any lock to HomeSeer you need to leave your controller connected to your HomeSeer computer and use the add node function in the Z-Wave management link to add your lock. Then move the lock to it's final location and optimize your network.

[drozwood90]

I agree with Rupp. To add all my locks, they had to be within 10' direct line of site to the stick.

In fact, I am currently testing moving the stick closer to the front door. I used to have GREAT communications with the front door, but then put a Freezer in the way. Had spotty communications since. Instead of purchasing a few "repeaters" to bounce the signal over, I happened to have a USB extender cable. {knock on wood} so far has been working well. By relocating the stick to within 10' of the front door, I have not missed a unlock yet. I also find I can still hit all the units that are in the basement. Normal units seem to have a MUCH greater transmit range than the locks themselves - esp. the Schlage. My Kwickset on the front door did not seem to have the same range issues.

--Dan