Announcement

Collapse
No announcement yet.

Fibaro Door Window Sensor + DS18B20

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • francrouge
    replied
    Originally posted by Tomgru View Post
    Sorry, the device is zip tied in a waterproof sleeve and mounted in my hottub shell. will take some time this weekend to get to it.
    the solution for you're information


    Piotr Wardęcki 28 Jun 18

    Hello,

    Yes, there is. Please go to the advanced settings of the DW sensor and find parameter 12.
    The maximum acceptable difference between the last reported temperature and the current temperature read from the sensor.
    If the temperatures differ by the set value or more, a report with the current temperature value is sent to the gateway.

    The default value is 8 which means the temperature needs to go up/down by 0.5 degree Celsius.
    Try value 4, that will increase the number of reports. Every change of 0.25 degree or more will be reported back to the main controller.

    You can find a manual of the device here:
    https://manuals.fibaro.com/content/m...SA-A-v1.01.pdf


    Pozdrawiam / Best regards

    Leave a comment:


  • francrouge
    replied
    Originally posted by Tomgru View Post
    Sorry, the device is zip tied in a waterproof sleeve and mounted in my hottub shell. will take some time this weekend to get to it.
    Hi fibaro wrote me back so don't unzipped you're device for nothing.


    Piotr Wardęcki 28 Jun 18

    Hello,

    Please note the version 2.5 is based on Z-wave chip 300 series and version 3.2 is Z-wave plus chip, series 500.
    These devices have different components. It`s not just firmware edition that differs the both device.

    Upgrading non Z-wave plus to version 3.2 is not possible. New firmware is not compatible with this version of Fibaro DW sensor.

    I apologize for the inconvenience


    Pozdrawiam / Best regards

    Piotr Wardęcki
    Technical Support Engineer

    Fibar Group S.A.
    ul. Lotnicza 1
    60-421 Poznań
    Poland

    Email: support@fibaro.com

    Leave a comment:


  • Tomgru
    replied
    Originally posted by francrouge View Post
    Hi just found out whats the problem

    I got the 2.5 firmware..

    The option 50 seem to be in firmware 3.5

    What firmware do you have ?
    Sorry, the device is zip tied in a waterproof sleeve and mounted in my hottub shell. will take some time this weekend to get to it.

    Leave a comment:


  • francrouge
    replied
    Originally posted by Tomgru View Post
    oh...I can help you here.. went round and around about this. Drove me nuts.
    Read final few posts here: https://forums.homeseer.com/showthre...ghlight=fibaro

    :-)
    Hi just found out whats the problem

    I got the 2.5 firmware..

    The option 50 seem to be in firmware 3.5

    What firmware do you have ?

    Leave a comment:


  • francrouge
    replied
    Originally posted by Tomgru View Post
    oh...I can help you here.. went round and around about this. Drove me nuts.
    Read final few posts here: https://forums.homeseer.com/showthre...ghlight=fibaro

    :-)
    I tried to change the parameter but i'm always getting error message.

    i tried to put 2 in value size and also i put 2700 in decimal for 45 min


    I tried to see if parameter number 50 was working and its giving me error message also
    Attached Files
    Last edited by francrouge; June 27th, 2018, 01:51 PM.

    Leave a comment:


  • Tomgru
    replied
    Originally posted by francrouge View Post
    My bad I didnt read that correctly i guest.

    Thx you so much i'm going to try that today.
    oh...I can help you here.. went round and around about this. Drove me nuts.
    Read final few posts here: https://forums.homeseer.com/showthre...ghlight=fibaro

    :-)

    Leave a comment:


  • francrouge
    replied
    Originally posted by cc4005 View Post
    3 clicks of the TMP button is for inclusion. Waking the device is a different procedure. See top of p.11.

    My bad I didnt read that correctly i guest.

    Thx you so much i'm going to try that today.

    Leave a comment:


  • cc4005
    replied
    3 clicks of the TMP button is for inclusion. Waking the device is a different procedure. See top of p.11.

    Leave a comment:


  • francrouge
    replied
    Originally posted by cc4005 View Post
    Periodic temperature reporting (parameter 52) is set to off by default. Have you tried changing the interval? https://manuals.fibaro.com/content/m...-EN-T-v2.0.pdf
    Hi thx for the info i didn't know i could do that.


    But i'm having issue to connect it to send the command.

    They tell you to press 3 time to wake up the device but it dosent seem do work.

    I'm gonna wait for the night maybe it will update..

    I'm going to keep you updated

    Leave a comment:


  • cc4005
    replied
    Periodic temperature reporting (parameter 52) is set to off by default. Have you tried changing the interval? https://manuals.fibaro.com/content/m...-EN-T-v2.0.pdf

    Leave a comment:


  • francrouge
    started a topic Fibaro Door Window Sensor + DS18B20

    Fibaro Door Window Sensor + DS18B20

    Hi guys

    I bought the fibaro door sensor for to monitor the temperature of my pool. With the DS18B20 . So far i added the sensor in homeseer and it seem to be working.

    But my main problem is that it dosent talk to homeseer frequently.

    I tried to change the amount of time i put 45 minutes for temps reading.

    But for exemple the last update was yesterday at 23h00 and now next day its 13h. So it dosent seem to update very much.

    Anybody got an idea i will put some picture of my config


    thx
    Attached Files
    Last edited by francrouge; July 1st, 2018, 06:31 PM. Reason: Solved
Working...
X