Announcement

Collapse
No announcement yet.

HomeSeer lighting is Here!

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ferraf
    replied
    Originally posted by jhearty View Post
    I finished installing these in my entire house, 25 WD100s, 12 WS100s and some WA100 slaves to go with both WS and WD switches. No issues with the WD100s at all. Three of the WS100s had the same on/off/on local control issue I reported earlier on this thread (25% defect rate). Two are running ceiling fans and the issue is not noticeable so I left them in. The other is for porch lights and Homeseer sent a replacement which is working fine.

    Lots of events written to control these including motion on & delayed off, single & double tap on and off events, all appear to be working as expected. I'm quite happy with the switches overall. They are IMO better than anything else out there and the price points were low enough to convince me to do the whole house. Bye bye X10.

    John
    I have a HS100 that has the flicker issue (On, Off then back On). Is this a defect and should be returned, or something a firmware upgrade should address?

    Leave a comment:


  • bandaid
    replied
    And it work. Thanks :-)

    Leave a comment:


  • bandaid
    replied
    Originally posted by macromark View Post
    We did have a small batch of switches that were mis-manufactured. If you ordered a HomeSeer HS-WA100+ non Z-Wave companion switch but received a Z-Wave Dragon WS100 instead, contact Aartech.ca to get a replacement.
    Done. Thanks for your help by the way! Now, I'm going to try to make this double tap work since I've few switchs that work :-)

    Leave a comment:


  • macromark
    replied
    Originally posted by bandaid View Post
    I'm really starting to get disappointed with the product... I've bought everything from www.aartech.ca because I want to avoid the brokerage fees. I bought switches, dimmers and companions. After doing the installation and going crazy about it because the companions were not working in the three way, Homeseer support found out that it was labeled and packaged has Homeseer wall companion WA-100+ but they were in fack HS-WS100+ that have been mislabel. To avoid time, problems and everything, I've manage to keep them since I was going to place an other order for some other stuff and since I was thinking that they were Homeseer products...

    Even the lamp module is shown as a DragonTech equipment...
    We did have a small batch of switches that were mis-manufactured. If you ordered a HomeSeer HS-WA100+ non Z-Wave companion switch but received a Z-Wave Dragon WS100 instead, contact Aartech.ca to get a replacement.

    Leave a comment:


  • bandaid
    replied
    Originally posted by waynehead99 View Post
    I don't think you bought a Homeseer switch. I don't remember them ever saying dragontech like your screenshot shows.

    The homeseer switches have the firmware for the double and triple tap... the dragontechs do not.
    I'm really starting to get disappointed with the product... I've bought everything from www.aartech.ca because I want to avoid the brokerage fees. I bought switches, dimmers and companions. After doing the installation and going crazy about it because the companions were not working in the three way, Homeseer support found out that it was labeled and packaged has Homeseer wall companion WA-100+ but they were in fack HS-WS100+ that have been mislabel. To avoid time, problems and everything, I've manage to keep them since I was going to place an other order for some other stuff and since I was thinking that they were Homeseer products...

    Even the lamp module is shown as a DragonTech equipment...

    Leave a comment:


  • waynehead99
    replied
    I don't think you bought a Homeseer switch. I don't remember them ever saying dragontech like your screenshot shows.

    The homeseer switches have the firmware for the double and triple tap... the dragontechs do not.

    Leave a comment:


  • bandaid
    replied
    Originally posted by macromark View Post
    Do you have a HomeSeer switch or a Dragon Tech switch? Please post your node information. It should look something like this:
    It seen to be an issue with the switch since I've tried with an other switch and it's working...
    Attached Files

    Leave a comment:


  • bandaid
    replied
    Originally posted by macromark View Post
    There should be 3 devices for each switch; a root device, control device and central scene device. It should look like the screen shot in this post: http://board.homeseer.com/showpost.p...9&postcount=15

    Also, this is the version information you should be seeing: 4.05 (ZDK 6.51.6) Firmware: 5.13
    Originally posted by macromark View Post
    Do you have a HomeSeer switch or a Dragon Tech switch? Please post your node information. It should look something like this:
    Hello again!

    1- Homeseer Smartstick +
    2- Homeseer Z-Wave Plug-In HS-PD100+
    4- Homeseer HS-WS100 +

    Original products... But it doesn't appear like it lol
    Attached Files

    Leave a comment:


  • macromark
    replied
    Originally posted by bandaid View Post
    Hello,

    Thanks for your help, I've tried the 3 solutions but doesn't seem like working.
    Do you have a HomeSeer switch or a Dragon Tech switch? Please post your node information. It should look something like this:
    Attached Files

    Leave a comment:


  • bandaid
    replied
    Originally posted by macromark View Post
    There should be 3 devices for each switch; a root device, control device and central scene device. It should look like the screen shot in this post: http://board.homeseer.com/showpost.p...9&postcount=15

    Also, this is the version information you should be seeing: 4.05 (ZDK 6.51.6) Firmware: 5.13
    Your talking about the que version of the HS3 or about the switch?

    Thanks :-)

    Leave a comment:


  • bandaid
    replied
    Originally posted by cheeryfool View Post
    For each switch you should get 3 HS3 devices if they added properly. You may have them, but have them hidden with your device filters - check that first.

    You are looking for one each of device types:

    - Z-Wave Switch Multilevel Root Device
    - Z-Wave Central Scene
    - Z-Wave Switch Multilevel

    You are currently only seeing the 3rd one in your screenshot.

    It's the Central Scene one that shows the different multi-tap statuses and that you use in your events to drive other things.

    If these devices are not just hidden, try re-scanning them from the Z-Wave tab of the ones that you can see. If that fails, try excluding them from the Z-Wave network and then re-adding them.
    Hello,

    Thanks for your help, I've tried the 3 solutions but doesn't seem like working.
    Attached Files

    Leave a comment:


  • macromark
    replied
    Originally posted by bandaid View Post
    Hello guys!

    I'm still new at this so... It's probably a noob question. I'm working with a Smartstick + and Homeseer WS-100 + and I can't get the double or triple tap feature on the controller. I think everything is up to date...


    Zwave plugin is 3.0.1.76
    HS100+ is on Version: 3,95 (Unknown) Firmware: 5.7 Hardware: 255

    Can anybody give me a clue about it?

    Thanks
    There should be 3 devices for each switch; a root device, control device and central scene device. It should look like the screen shot in this post: http://board.homeseer.com/showpost.p...9&postcount=15

    Also, this is the version information you should be seeing: 4.05 (ZDK 6.51.6) Firmware: 5.13

    Leave a comment:


  • cheeryfool
    replied
    For each switch you should get 3 HS3 devices if they added properly. You may have them, but have them hidden with your device filters - check that first.

    You are looking for one each of device types:

    - Z-Wave Switch Multilevel Root Device
    - Z-Wave Central Scene
    - Z-Wave Switch Multilevel

    You are currently only seeing the 3rd one in your screenshot.

    It's the Central Scene one that shows the different multi-tap statuses and that you use in your events to drive other things.

    If these devices are not just hidden, try re-scanning them from the Z-Wave tab of the ones that you can see. If that fails, try excluding them from the Z-Wave network and then re-adding them.

    Leave a comment:


  • bandaid
    replied
    Hello guys!

    I'm still new at this so... It's probably a noob question. I'm working with a Smartstick + and Homeseer WS-100 + and I can't get the double or triple tap feature on the controller. I think everything is up to date...


    Zwave plugin is 3.0.1.76
    HS100+ is on Version: 3,95 (Unknown) Firmware: 5.7 Hardware: 255

    Can anybody give me a clue about it?

    Thanks
    Attached Files

    Leave a comment:


  • bandaid
    replied
    Can't get double tap

    Hello guys,

    I'm still new with Homeseer and I've a hard time to get the double and triple tap working. I think that everything is up to date... Can any body give me a clue?

    I'm working with a Smarstick + and the new Homeseer Lightning Ws100 +(Version: 3,95 (Unknown) Firmware: 5.7 Hardware: 255)

    Thanks!
    Attached Files

    Leave a comment:

Working...
X