Announcement

Collapse
No announcement yet.

Status errors

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Status errors

    Pretty much a newby here.

    I installed 7 of these guys about 6 weeks ago and they were all working pretty good until 4 days ago, when I noticed some were not motion triggering and the motion status indicators seemed random and non-changing. I forced a poll and see they all show status errors on Luminance/Switch status, and the Flood/Motion status does not show errors but does not appear to be functional. Any general direction would be appreciated...

    83 @ Polling: Exterior Z2 Den NE HomeSeer Floodlight Sensor (Status is: 0)
    82 @ Polling: Exterior Z2 Den NE Motion Sensor (Status is: 0)
    81 @ Polling: Exterior Z2 Den NE Luminance (Status isPlugin Reports Error Getting Status))
    80 @ Polling: Exterior Z2 Den NE Switch (Status isPlugin Reports Error Getting Status))
    79 @ Polling: Exterior Z3 MBR E HomeSeer Floodlight Sensor (Status is: 0)
    78 @ Polling: Exterior Z3 MBR E Motion Sensor (Status is: 0)
    77 @ Polling: Exterior Z3 MBR E Luminance (Status isPlugin Reports Error Getting Status))
    76 @ Polling: Exterior Z3 MBR E Switch (Status isPlugin Reports Error Getting Status))
    75 @ Polling: Exterior Z4 MBR S HomeSeer Floodlight Sensor (Status is: 0)
    74 @ Polling: Exterior Z4 MBR S Motion Sensor (Status is: 0)
    73 @ Polling: Exterior Z4 MBR S Switch (Status isPlugin Reports Error Getting Status))
    72 @ Polling: Exterior Z4 MBR S Luminance (Status isPlugin Reports Error Getting Status))
    71 @ Polling: Exterior Z5 LR NW HomeSeer Floodlight Sensor (Status is: 0)
    70 @ Polling: Exterior Z5 LR NW Motion Sensor (Status is: 0)
    69 @ Polling: Exterior Z5 LR NW Luminance (Status isPlugin Reports Error Getting Status))
    68 @ Polling: Exterior Z5 LR NW Switch (Status isPlugin Reports Error Getting Status))
    67 @ Polling: Exterior Z6 Gar WS HomeSeer Floodlight Sensor (Status is: 0)
    66 @ Polling: Exterior Z6 Gar WS Motion Sensor (Status is: 0)
    65 @ Polling: Exterior Z6 Gar WS Luminance (Status isPlugin Reports Error Getting Status))
    64 @ Polling: Exterior Z6 Gar WS Switch (Status isPlugin Reports Error Getting Status))
    63 @ Polling: Exterior Z7 Gar WN HomeSeer Floodlight Sensor (Status is: 0)
    62 @ Polling: Exterior Z7 Gar WN Motion Sensor (Status is: 0)
    61 @ Polling: Exterior Z7 Gar WN Luminance (Status isPlugin Reports Error Getting Status))
    60 @ Polling: Exterior Z7 Gar WN Switch (Status isPlugin Reports Error Getting Status))
    59 @ Polling: Exterior Z8 GBR SW HomeSeer Floodlight Sensor (Status is: 0)
    58 @ Polling: Exterior Z8 GBR SW Motion Sensor (Status is: 0)
    57 @ Polling: Exterior Z8 GBR SW Luminance (Status isPlugin Reports Error Getting Status))
    56 @ Polling: Exterior Z8 GBR SW Switch (Status isPlugin Reports Error Getting Status))

    #2
    Do you have other Z-Wave devices in your network and are they still working? The fact that 7 of these are not working would point to an issue with your Z-Wave interface unless other devices are working.
    -Rupp
    sigpic

    Comment


      #3
      No, just these 7 sensors. I have tried toggling the PI and restarting the ZS2. I see no errors in the log for any z wave line. I went the root device on a couple nodes, Z-wave tab, and did a Test Connectivity with result "Failed to reach node X". Audit also failed with an "not able to send frame". I toggled the PI, nada. Rebooted the ZS2. Today, I relocated the ZS2 a few feet from one of the sensors (node 2, Z2 Den NE) and tried Test Connectivity, which failed, then a Rescan, then a Test Connectivity, which again failed. Log output below. I'm stymied.
      Jul-05 2:57:43 PM Z-Wave 3 out of 3 Child devices of node 2 were created successfully.
      Jul-05 2:57:37 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:57:30 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:57:24 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:57:18 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:57:11 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:57:05 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:56:59 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:56:52 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:56:28 PM Z-Wave Instant status for Z-Wave device Exterior Z2 Den NE HomeSeer Floodlight Sensor (2) failed. The command will be queued and sent when it next wakes up.
      Jul-05 2:56:21 PM Z-Wave Enabling instant status for Z-Wave device Exterior Z2 Den NE HomeSeer Floodlight Sensor (2)
      Jul-05 2:56:15 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:56:09 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:56:01 PM Z-Wave Internal: Adding association for Z-Wave device Exterior Z2 Den NE HomeSeer Floodlight Sensor (Node 2, Group 1) to HomeSeer
      Jul-05 2:55:55 PM Z-Wave Getting association information for Exterior Z2 Den NE HomeSeer Floodlight Sensor
      Jul-05 2:55:49 PM OMNI ---------------------------
      Jul-05 2:55:49 PM OMNI Plugin startup is complete.
      Jul-05 2:55:49 PM OMNI ---------------------------
      Jul-05 2:55:49 PM OMNI Synchronization complete.
      Jul-05 2:55:42 PM Z-Wave Getting association information for node 2
      Jul-05 2:55:36 PM Z-Wave Error Exception creating Sensor Multilevel child device of node 2, GET for supported sensor types indicated failure.
      Jul-05 2:55:18 PM Z-Wave Node 2 is a Z-Wave Plus node. Retrieving ZWPlus Info...
      Jul-05 2:55:18 PM Z-Wave Node 2 is Z-Wave version: Lib: 5.03 App: 1.4
      Jul-05 2:55:18 PM Z-Wave Warning Error getting version information for node 2, Send failed.
      Jul-05 2:55:11 PM Z-Wave Node: 2 Supports Class(es): ZWAVEPLUS_INFO, ASSOCIATION, ASSOCIATION_GRP_INFO, TRANSPORT_SERVICE, VERSION_V2, MANUFACTURER_SPECIFIC_V2, DEVICE_RESET_LOCALLY, POWERLEVEL, SECURITY_2, SUPERVISION, FIRMWARE_UPDATE_MD_V4, NOTIFICATION_V6, SWITCH_BINARY, SENSOR_MULTILEVEL, CONFIGURATION, SENSOR_BINARY_V2
      Jul-05 2:55:11 PM Z-Wave Syncing Z-Wave nodes with device list...
      Jul-05 2:55:11 PM Z-Wave Found 8 Z-Wave nodes
      Jul-05 2:55:11 PM Z-Wave Getting Z-Wave node list for network CC0D46E8...
      Jul-05 2:54:16 PM Z-Wave Starting Z-Wave Polling for Network CC0D46E8...

      Comment


        #4
        Problem solved. Root cause: user is an idiot. The actual problem is that several days ago a scene had been triggered which set all the Lutron switches that power the floodlights to off. No power, no response. This does lead back to a realization I had soon after installing these sensors: the floods should probably be wired hot, not switched. Not sure how I'll get around this one. I could pull the switches and do a pass-through power connection, but then I have 7 holes to fill.

        Comment


          #5
          When I replaced an existing Flood Light withe the FLS, I wired around the existing switch(z-wave) so the flood has constant power. THEN, with the "load" side of the switch disconnected but the switch still powered, I made the switch a "remote" and with some events it would turn the flood on or off so I still had manual control of the lights.

          Comment


            #6
            Originally posted by BobSpen View Post
            When I replaced an existing Flood Light withe the FLS, I wired around the existing switch(z-wave) so the flood has constant power. THEN, with the "load" side of the switch disconnected but the switch still powered, I made the switch a "remote" and with some events it would turn the flood on or off so I still had manual control of the lights.
            Thats perfect. Thanks!

            Comment


              #7
              So one way to do that would be to "link" the Lutron switch to the node switch...? Or I could make the node switch be event driven by a Lutron press and/or other, right? Any pro/cons either way?

              Comment


                #8
                Either way. Event driven gives you more future possibilities.

                Comment

                Working...
                X