I installed 7 FLS100+ gen 1 several months ago and 6 have been fairly reliable. But one of the 6 filled up completely with water during a recent storm (how does that happen?) and shorted out. I could hear it frying before I disconnected power. I bought 2 G2's and replaced the fried gen 1.
I don't know if I am missing something or if the sensor is missing something, but the G2 has no light control child. Node 8 below is one of the old FLS100 and Node 9 is the G2. Where is my On/Off control? I also can't get to Settings (greyed out), and auditing the node gives me
"This node supports associations on the following groups:
Node is missing Association Groups information."
I've tried removing and re-adding the device with no love.
OLD SENSOR, WITH LIGHT CONTROL
G2 SENSOR WITHOUT LIGHT CONTROL
Full Name: Zwave Node 8 SW Floodlight Sensor Polling: Polling Disabled
Manufacturer:
HomeSeer Technologies LLC Type:
0x201 ID:
0xB Listens:
Yes Version: 5.03 (ZDK 6.71.3) Firmware: 1.4 Hardware: 1 Neighbor Count:
2 Speed:
100Kbps
Neighbors: 5, 6
Last Working Route: 5 (100K) Set Route:
Uses Interface: Zee S2 Internal (1) Basic Type: ROUTING SLAVE, Generic Type: SENSOR NOTIFICATION, Specific Type: NOTIFICATION SENSOR
Command Classes:
Supported: Zwaveplus Info, Association, Association Grp Info, Transport Service, Version, Manufacturer Specific, Device Reset Locally, Powerlevel, Security 2, Supervision, Firmware Update Md, Notification(V 4), Switch Binary(V 1), Sensor Multilevel(V 5), Configuration, Sensor Binary
Child Device: SW Motion Sensor CC: Notification Ver: 4 Polling: Polling Disabled
Child Device: SW Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Disabled
Child Device: SW Floodlight CC: Switch Binary Polling: Polling Disabled
Child Device: Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Disabled
9 Full Name: Node 9 Z-Wave HomeSeer Notification Sensor Polling: Polling Disabled
Manufacturer:
HomeSeer Technologies LLC Type:
0x201 ID:
0xC Listens:
Yes Version: 6.08 (Unknown) Firmware: 1.0 Hardware: 1 Neighbor Count:
3 Speed:
40Kbps
Neighbors: 1, 2, 4
Last Working Route: Direct (40K) Set Route:
Uses Interface: Zee S2 Internal (1) Basic Type: ROUTING SLAVE, Generic Type: SENSOR NOTIFICATION, Specific Type: NOTIFICATION SENSOR
Command Classes:
Supported: Unknown, Association, Multi Channel Association, Association Grp Info, Transport Service, Version, Manufacturer Specific, Device Reset Locally, Powerlevel, Security 2, Supervision, Firmware Update Md, Notification(V 8), Network Management Installation Maintenance, Sensor Multilevel(V 5), Configuration, Sensor Binary(V 1)
Child Device: Notification CC: Notification Ver: 8 Polling: Polling Interval: 20m, 4s
Child Device: Sensor Binary CC: Sensor Binary Polling: Polling Interval: 20m, 6s
Child Device: Home Security CC: Notification Ver: 8 Polling: Polling Interval: 20m, 8s
Child Device: Temperature CC: Sensor Multilevel Ver: 5 Polling: Polling Interval: 20m, 10s
Child Device: Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Interval: 20m, 12s
I don't know if I am missing something or if the sensor is missing something, but the G2 has no light control child. Node 8 below is one of the old FLS100 and Node 9 is the G2. Where is my On/Off control? I also can't get to Settings (greyed out), and auditing the node gives me
"This node supports associations on the following groups:
Node is missing Association Groups information."
I've tried removing and re-adding the device with no love.
OLD SENSOR, WITH LIGHT CONTROL
G2 SENSOR WITHOUT LIGHT CONTROL
Full Name: Zwave Node 8 SW Floodlight Sensor Polling: Polling Disabled
Manufacturer:
HomeSeer Technologies LLC Type:
0x201 ID:
0xB Listens:
Yes Version: 5.03 (ZDK 6.71.3) Firmware: 1.4 Hardware: 1 Neighbor Count:
2 Speed:
100Kbps
Neighbors: 5, 6
Last Working Route: 5 (100K) Set Route:
Uses Interface: Zee S2 Internal (1) Basic Type: ROUTING SLAVE, Generic Type: SENSOR NOTIFICATION, Specific Type: NOTIFICATION SENSOR
Command Classes:
Supported: Zwaveplus Info, Association, Association Grp Info, Transport Service, Version, Manufacturer Specific, Device Reset Locally, Powerlevel, Security 2, Supervision, Firmware Update Md, Notification(V 4), Switch Binary(V 1), Sensor Multilevel(V 5), Configuration, Sensor Binary
Child Device: SW Motion Sensor CC: Notification Ver: 4 Polling: Polling Disabled
Child Device: SW Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Disabled
Child Device: SW Floodlight CC: Switch Binary Polling: Polling Disabled
Child Device: Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Disabled
9 Full Name: Node 9 Z-Wave HomeSeer Notification Sensor Polling: Polling Disabled
Manufacturer:
HomeSeer Technologies LLC Type:
0x201 ID:
0xC Listens:
Yes Version: 6.08 (Unknown) Firmware: 1.0 Hardware: 1 Neighbor Count:
3 Speed:
40Kbps
Neighbors: 1, 2, 4
Last Working Route: Direct (40K) Set Route:
Uses Interface: Zee S2 Internal (1) Basic Type: ROUTING SLAVE, Generic Type: SENSOR NOTIFICATION, Specific Type: NOTIFICATION SENSOR
Command Classes:
Supported: Unknown, Association, Multi Channel Association, Association Grp Info, Transport Service, Version, Manufacturer Specific, Device Reset Locally, Powerlevel, Security 2, Supervision, Firmware Update Md, Notification(V 8), Network Management Installation Maintenance, Sensor Multilevel(V 5), Configuration, Sensor Binary(V 1)
Child Device: Notification CC: Notification Ver: 8 Polling: Polling Interval: 20m, 4s
Child Device: Sensor Binary CC: Sensor Binary Polling: Polling Interval: 20m, 6s
Child Device: Home Security CC: Notification Ver: 8 Polling: Polling Interval: 20m, 8s
Child Device: Temperature CC: Sensor Multilevel Ver: 5 Polling: Polling Interval: 20m, 10s
Child Device: Luminance CC: Sensor Multilevel Ver: 5 Polling: Polling Interval: 20m, 12s
Comment