Announcement

Collapse
No announcement yet.

Hometroller ZEE - Everspring ST814 update error

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Hometroller ZEE - Everspring ST814 update error

    Hi,

    I have a ST814 sensor (temperature/humidity) and used to update relatively OK but, recently, does not update anymore. The log shows the following error:

    "Node Change Event for Node 8 on Network 016A24AB, CC=COMMAND_CLASS_SENSOR_MULTILEVEL_V3 but no valid devices were found. (31-05-05-01-35-F8)"

    I have updated to version 3.0.0.97 recently - can this be the cause?
    anyone else experiencing this issue?

    Thanks,

    #2
    There's another post about the ST814-2 having problems with the latest z-wave release.
    You can try to wake it up and rescan and see if that fixes it.
    HS4Pro Running on a Raspberry Pi4
    79 Z-Wave Nodes, 131 Events, 383 Devices
    Z-Wave, UPB, WiFi
    Plugins: EasyTrigger, weatherXML, OMNI, Z-Wave, Tuya, Device History
    HSTouch Clients: 3 Android, 1 Joggler

    Comment


      #3
      I did rescan, it updates the temperature during the rescan, but no updates after that

      Comment


        #4
        See this post.
        http://board.homeseer.com/showthread.php?t=167547
        -Rupp
        sigpic

        Comment


          #5
          Thanks Rupp
          I will try the proposed solution

          Comment


            #6
            Finally I found some time to play again with the sensor...

            I have set the root device wake-up interval to 12 min


            I have set the sensor polling interval to 1 min (I have tried 6 min also)

            The log shows that the device sends weak up notifications every 12 min (aprox)



            ..but the temperature still does not update on a regular basis ... sometime does not update for 10 hours
            Is there something else that I should do/check so solve this issue?

            Thanks

            Comment


              #7
              What version of the Z-Wave plugin are you running? Latest version is 3.0.0.158

              Comment


                #8
                Where have you bean Kaldoon? Welcome back. You had us worried.

                I was going to post a "where's waldo picture" just a couple of days ago.



                Primary Homeseer Zee Z-Wave updates are going a bit slower and probably relate to mostly HS3 updates' testing/validation HS3 wintel first; then HS3 linux; well at least from what I have seen with the Homeseer Zee.
                Last edited by Pete; June 21, 2014, 01:19 PM.
                - Pete

                Auto mator
                Homeseer 3 Pro - 3.0.0.548 (Linux) - Ubuntu 18.04/W7e 64 bit Intel Haswell CPU 16Gb
                Homeseer Zee2 (Lite) - 3.0.0.548 (Linux) - Ubuntu 18.04/W7e - CherryTrail x5-Z8350 BeeLink 4Gb BT3 Pro
                HS4 Lite - Ubuntu 20.04 / VB W7e Jetway JBC420U591
                Fanless IntelĀ® Celeron N3160 SoC 8Gb
                HS4 Pro - V4.1.18.1 - Ubuntu 20.04/VB W7e 64 bit Intel Kaby Lake CPU - 32Gb
                HSTouch on Intel tabletop tablets

                X10, UPB, Zigbee, ZWave and Wifi MQTT automation-Tasmota-Espurna. OmniPro 2, Russound zoned audio, Smartthings hub, Hubitat Hub, and Home Assistant

                Comment


                  #9
                  I am running HS3 Zee Edition 3.0.0.97

                  Comment


                    #10
                    I've been running the 103 beta with much fewer errors, now installing the latest 106 release...

                    Edit: Still the same intermittent errors (Sensor 9 is Outside)...

                    un-29 2:21:22 PM Z-Wave Error Node Change Event for Node 9 on Network 016A2698, CC=COMMAND_CLASS_SENSOR_MULTILEVEL_V3 but no valid devices were found. (31-05-01-2A-03-5D)
                    Jun-29 2:12:26 PM Z-Wave Device: Main Inside Sensor Temp Set to 80.6 (F)
                    Jun-29 1:58:13 PM Z-Wave Device: Main Inside Sensor Temp Set to 80.2 (F)
                    Jun-29 1:29:54 PM Z-Wave Device: Main Inside Sensor Temp Set to 80 (F)
                    Jun-29 1:28:30 PM Z-Wave Device: Main Outside Sensor Humidity Set to 42 (%)
                    Jun-29 1:28:29 PM Z-Wave Error Node Change Event for Node 9 on Network 016A2698, CC=COMMAND_CLASS_SENSOR_MULTILEVEL_V3 but no valid devices were found. (31-05-01-2A-03-5C)
                    Jun-29 1:25:03 PM Web Server Web Server authorized login successful from: 192.155.95.251 User: mike
                    Jun-29 1:15:45 PM Z-Wave Device: Main Inside Sensor Temp Set to 79.8 (F)
                    Jun-29 1:15:00 PM Log Info The log database is currently 0.08MB in size.
                    Jun-29 12:47:19 PM Z-Wave Device: Main Inside Sensor Humidity Set to 59 (%)
                    Jun-29 12:47:19 PM Z-Wave Device: Main Inside Sensor Temp Set to 79.5 (F)
                    Jun-29 12:35:37 PM Z-Wave Error Node Change Event for Node 9 on Network 016A2698, CC=COMMAND_CLASS_SENSOR_MULTILEVEL_V3 but no valid devices were found. (31-05-01-2A-03-58)
                    Last edited by NutsyHome; June 29, 2014, 01:24 PM.

                    Comment

                    Working...
                    X