Announcement

Collapse
No announcement yet.

HS3 and CM15A not working ..

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • HS3 and CM15A not working ..

    Upgraded from HS2 to HS3 and I cannot get the CM15A plugin to work (it's working fine in HS2)

    On the Installed Plug-In page it tells me the plug-in status for CM15A is OK. The com port states N/A (though it should be visible on a COM port right??)

    There's no X10 tab to be found anywhere and when I try to switch on/off an X10 device nothing happens either.

    Tried to use the CM11A (on COM1 for me) instead .. but that's not working either .. (**FATAL**: Unable to communicate with CM11A, no response to status request) (CM15A plugin is disabled when I try this)

  • #2
    What OS are you using? Linus or Windows (Windows what?).

    Here have only tested the CM11A on Linux HS3 and it works fine.

    Have a look at these posts relating to connecting / using an X10 CM15A/CM11A on Windows.

    HomeSeer X10 Plug-in
    - Pete

    Auto mator
    Homeseer 3 Pro - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e 64 bit Intel Haswell CPU - Mono 6.00
    Homeseer Zee2 (Lite) - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e - CherryTrail x5-Z8350 BeeLink 4Gb BT3 Pro - Mono 6.00

    X10, UPB, Zigbee, ZWave and Wifi MQTT automation.

    Comment


    • #3
      Hi Pete,

      It's a W10 system

      Comment


      • #4
        It should work fine.

        Make sure no other software is running that uses the serial com for the CM11A.

        Download the following free software to test your CM11A and com port connection.

        Free Windows X10 software
        - Pete

        Auto mator
        Homeseer 3 Pro - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e 64 bit Intel Haswell CPU - Mono 6.00
        Homeseer Zee2 (Lite) - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e - CherryTrail x5-Z8350 BeeLink 4Gb BT3 Pro - Mono 6.00

        X10, UPB, Zigbee, ZWave and Wifi MQTT automation.

        Comment


        • #5
          It's a CM15A .. shouldn't I be using that driver?

          This is what I see in the log:
          apr-24 20:59:39 Device Control Device: Groundfloor TV Room Light to Off (3) by/from: CAPI Control Handler

          But nothing happens ..

          The CM15A works fine in HS2 (which is not running when I test HS3)

          The device I've added was added as described here

          Comment


          • #6
            I thought you had both a CM11A and CM15A.

            I would first try it with the CM11A.
            - Pete

            Auto mator
            Homeseer 3 Pro - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e 64 bit Intel Haswell CPU - Mono 6.00
            Homeseer Zee2 (Lite) - 3.0.0.534 (Linux) - Ubuntu 18.04/W7e - CherryTrail x5-Z8350 BeeLink 4Gb BT3 Pro - Mono 6.00

            X10, UPB, Zigbee, ZWave and Wifi MQTT automation.

            Comment

            Working...
            X