Thanks, I have just experimented several times while watching the Log.
- I ran the event to send the message and instantly got a Log saying the event has run.
- 55 Seconds later i got 'Pushover Notification Sent' in the Log
- 1 Second later The Notification came through.
Announcement
Collapse
No announcement yet.
HS3 Pushover Plugin
Collapse
X
-
Originally posted by Pricey1985 View PostI to have been experiencing delays for the past few months, prior to that it was almost instantaneous. The delays are constantly between 30-90 seconds.
I was leaning towards it being an issue with our Samsung Phones, however, I have tried simultaneously sending a message via Homeseer and via the pushover.net webpage and the webpage is always instant then the Homeseer Message comes through a minute later.
If you send a message from a HS event and there is a delay between sending and getting the sent message in the log then I can look at that but if HS gets the sent notification instantly (I suspect it does) then I'm afraid there is little I can do to figure out where the issue is.
- Likes 1
Leave a comment:
-
I to have been experiencing delays for the past few months, prior to that it was almost instantaneous. The delays are constantly between 30-90 seconds.
I was leaning towards it being an issue with our Samsung Phones, however, I have tried simultaneously sending a message via Homeseer and via the pushover.net webpage and the webpage is always instant then the Homeseer Message comes through a minute later.
Leave a comment:
-
Originally posted by Ltek View Postmrhappy
Can we use RegX or something else to parse variable data from with the "Message Body" section?
The data in the source HS3 Device needs to be 'cleaned up'; this is the full text data...
" #3 3/20/2019 10:48:38 AM User Robyn - Phone Tracking entered Town Club "
I only want... "entered Town Club" to be sent in Message Body
thx!
Leave a comment:
-
Originally posted by The Profit View Post
I do not have the desktop client, I’ll download it and give it a try. Normally I don’t have any noticeable delay at all, it’s just been lately that I have noticed it for the last month or so. I figured it could have just been a temporary delay but it seems to have been consistent.
Sent from my iPad using Tapatalk
I'd be looking at seeing whether there is anything common to your mobile devices or reaching out to Pushover about it - their support were pretty helpful when I contacted them, you can give them the message ID from the plugin webpage and they can check their end.
Leave a comment:
-
Originally posted by mminehan View Post
I'm in New Zealand, quite some distance from the Pushovr servers, and there is only a 2 or 3 second delay for mobile devices in our system. Have you got the desktop client (free for 7 days) to check if it is a recieveing or sending delay?
Sent from my iPad using Tapatalk
Leave a comment:
-
Originally posted by The Profit View Postmrhappy I have been using your plugin for quite some time and it has been great but I've noticed lately that there is a 20-30 delay between when HS triggers the event to send the message and when it is received on our phones. I can see that it's not on the HS side or the plugin that is causing the delay, it just seems to be the time from Pushover to our phones. It doesn't seem to make a difference if we are on wifi or cell data. Have you experienced these kinds of delays and is there any way fix it?
Thank you!
Leave a comment:
-
mrhappy I have been using your plugin for quite some time and it has been great but I've noticed lately that there is a 20-30 delay between when HS triggers the event to send the message and when it is received on our phones. I can see that it's not on the HS side or the plugin that is causing the delay, it just seems to be the time from Pushover to our phones. It doesn't seem to make a difference if we are on wifi or cell data. Have you experienced these kinds of delays and is there any way fix it?
Thank you!
Leave a comment:
-
I take your point about a forum, perhaps I'll make contact with HST but there official line was always that if it wasn't for sale then you didn't get a forum.
- Likes 1
Leave a comment:
-
Originally posted by shill View PostI've just installed the plugin, and am really excited to get it working. However, I'm having trouble and trying to see if there are answers to my questions in this single thread is nearly impossible. I'd highly recommend asking HST to set up a forum. Even if you're not too concerned about it, it would GREATLY help your users, and probably most importantly, it would help them help OTHER users better and take some pressure off you
My issue is that every time I try to add an event action, I fill out the fields (except for the optional ones), and when I attempt to close the action, it resets all the arguments...
NEVER MIND! I've never seen a plugin with an "Update" button in the action so I didn't even notice it.
I take your point about a forum, perhaps I'll make contact with HST but there official line was always that if it wasn't for sale then you didn't get a forum.
Leave a comment:
-
I've just installed the plugin, and am really excited to get it working. However, I'm having trouble and trying to see if there are answers to my questions in this single thread is nearly impossible. I'd highly recommend asking HST to set up a forum. Even if you're not too concerned about it, it would GREATLY help your users, and probably most importantly, it would help them help OTHER users better and take some pressure off you
My issue is that every time I try to add an event action, I fill out the fields (except for the optional ones), and when I attempt to close the action, it resets all the arguments...
NEVER MIND! I've never seen a plugin with an "Update" button in the action so I didn't even notice it.
- Likes 1
Leave a comment:
-
Originally posted by mrhappy View Post
Strange as I'm sure that historically the time/date replacement variables did NOT have the SAPI tags in, that said at some point I added some custom replacement variables to the plugin as per the attached picture so I must've had reasons for it. When included in a message they should do the same job so please give it a try.
Leave a comment:
-
Originally posted by prsmith777 View Post
Yeah that's the problem. I have a mega script that creates all my announcements and I use the announcement message to send pushover messages if we are away from the house. If there is no convenient work around, I am going to have to rewrite the script to create two separate messages, one for announcement and one for pushover.
1 Photo
Leave a comment:
-
Originally posted by Tj in Bristol View Poston version 0.0.0.45 of the Pushover Plugin in homeseer pro3 in windows, iPhone client , get the Unknown Exception in Pushmessage Object reference not set to an instance of an object.
can you please how to fix it , i really want to see this work, thank you, Tj
Has it worked for you before...if so do you know which version you updated from?
Secondly can you attach a screenshot of your event?
Leave a comment:
-
on version 0.0.0.45 of the Pushover Plugin in homeseer pro3 in windows, iPhone client , get the Unknown Exception in Pushmessage Object reference not set to an instance of an object.
can you please how to fix it , i really want to see this work, thank you, Tj
to get this up and running on pushover create and app, attach a icon, i used homeseer, copy the app code and set it up in the configure screen
tha is really cool now it work, home this helps someone....Tj
Leave a comment:
Leave a comment: