I recently noticed that after HS restarts (automatically each Wednesday morning), my events that have Elk Panel actions are blank. In the log, I see the following at startup:
6/14/2006 4:45:42 PM Info Done initializing infrared interface
6/14/2006 4:45:42 PM Info Initializing Plug-in: ELK-M1
6/14/2006 4:45:42 PM Elk-M1 Register callback Version 2.2.6
6/14/2006 4:45:42 PM COM Plugin Calling InitIO
6/14/2006 4:45:45 PM Elk-M1 Connecting to IP 192.168.1.55
6/14/2006 4:45:50 PM COM Plugin Info Elk-M1 Ethernet Initializing...
6/14/2006 4:45:51 PM COM Plugin InitIO error: Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM COM Plugin Error Error initializing Custom Interface: Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM Error Initializing interface: ELK-M1->Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM Info Done initializing plug-in ELK-M1
6/14/2006 4:45:51 PM Info Initializing Plug-in: WAPSEER-20
I think that this started happending after I updated to the latest WAPSEER-20 from the updater - but I am not sure.
If I go to the Setup/interfaces page and disable and then enable the Elk-M1 plug in, I see a normal log without the errors:
6/14/2006 5:01:04 PM Info Shutting down generic Plug-In: ELK-M1
6/14/2006 5:01:18 PM Info Initializing Plug-in: ELK-M1
6/14/2006 5:01:18 PM Elk-M1 Register callback Version 2.2.6
6/14/2006 5:01:18 PM COM Plugin Calling InitIO
6/14/2006 5:01:18 PM Info Done initializing plug-in ELK-M1
Also, once I disable and enable the plug in, then all the Elk panel actions re-appear in all the appropriate events.
Any idea what is going on here? Or how to re-init or circumvent?
thanks very much!
6/14/2006 4:45:42 PM Info Done initializing infrared interface
6/14/2006 4:45:42 PM Info Initializing Plug-in: ELK-M1
6/14/2006 4:45:42 PM Elk-M1 Register callback Version 2.2.6
6/14/2006 4:45:42 PM COM Plugin Calling InitIO
6/14/2006 4:45:45 PM Elk-M1 Connecting to IP 192.168.1.55
6/14/2006 4:45:50 PM COM Plugin Info Elk-M1 Ethernet Initializing...
6/14/2006 4:45:51 PM COM Plugin InitIO error: Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM COM Plugin Error Error initializing Custom Interface: Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM Error Initializing interface: ELK-M1->Wrong protocol or connection state for the requested transaction or request
6/14/2006 4:45:51 PM Info Done initializing plug-in ELK-M1
6/14/2006 4:45:51 PM Info Initializing Plug-in: WAPSEER-20
I think that this started happending after I updated to the latest WAPSEER-20 from the updater - but I am not sure.
If I go to the Setup/interfaces page and disable and then enable the Elk-M1 plug in, I see a normal log without the errors:
6/14/2006 5:01:04 PM Info Shutting down generic Plug-In: ELK-M1
6/14/2006 5:01:18 PM Info Initializing Plug-in: ELK-M1
6/14/2006 5:01:18 PM Elk-M1 Register callback Version 2.2.6
6/14/2006 5:01:18 PM COM Plugin Calling InitIO
6/14/2006 5:01:18 PM Info Done initializing plug-in ELK-M1
Also, once I disable and enable the plug in, then all the Elk panel actions re-appear in all the appropriate events.
Any idea what is going on here? Or how to re-init or circumvent?
thanks very much!
Comment