Announcement

Collapse
No announcement yet.

Version question

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • rschein
    replied
    Thanks.

    Leave a comment:


  • rmasonjr
    replied
    according to this thread, it is now part of HS natively:
    http://board.homeseer.com/showthread.php?p=953626

    Leave a comment:


  • rschein
    replied
    If that's what is needed. I can't seem to find it in the ftp directory. Would another updater for .44 make it better?

    Leave a comment:


  • rschein
    replied
    Could you post the dll? It's the only errors generated in my log (lots mostly timeouts) I can throw it in the root directory and see if life becomes better.

    Leave a comment:


  • Wadenut
    replied
    Confirmed. It's not there. The uncanny thing is, the plugin is enabled and is functioning. I installed this from the updater not more than a month ago. Is it possible we're looking at two different versions altogether?

    Leave a comment:


  • rmasonjr
    replied
    Mine is in the root homeseer folder: HSPI_ZWAVETHERM.dll

    Leave a comment:


  • Wadenut
    replied
    Originally posted by rschein View Post
    Where's the DLL in .44 I've looked in the program folder and don't find it and a search of the system doesn't find it either.
    Ditto here.
    Ditto on the version #
    and
    Most of my errors/warnings happen to be on the thermostat.

    Leave a comment:


  • rschein
    replied
    Where's the DLL in .44 I've looked in the program folder and don't find it and a search of the system doesn't find it either.

    Leave a comment:


  • rmasonjr
    replied
    Yeah, it does look odd that it says N/A under the version column. Mine reports 1.3.0.8.
    The date/time on the DLL is 1/15/2009 9:10 AM

    Leave a comment:


  • rschein
    replied
    I am still questioning if I have a version conflict. It shows as N/A unless it is disabled then it shows .44 (32 bit xp showed 44 version) is there a good way to flush it out and insure 44 is installed?
    Attached Files

    Leave a comment:


  • rmasonjr
    replied
    Originally posted by rschein View Post
    Okay. I tried the immediate command and setting debug in the thermostat device. Neither makes a difference. I didn't understand the comment about the z-wave module being a problem. Is it the Aeon stick Homerseer sold me or the thermostat that they sold me that has a bad module in it?
    Sorry - In the .43 release thread, we started seeing more of these poll failure messages than we did on previous versions. When I mentioned this, we were informed that discontinued/older zwave devices can contribute to these messages - even though previous versions of HS did not have this problem. I asked for a list of known modules and the list received back were Monster and first-generation Intermatic.

    I am skeptical of this response from HS given the fact that .43/.44 has more poll failures than previous versions. So, I was merely commenting on what we've been told by HST as the potential cause. My opinion is that it is a z-wave timing issue caused by HS.

    Leave a comment:


  • rschein
    replied
    Okay. I tried the immediate command and setting debug in the thermostat device. Neither makes a difference. I didn't understand the comment about the z-wave module being a problem. Is it the Aeon stick Homerseer sold me or the thermostat that they sold me that has a bad module in it?

    Leave a comment:


  • Wadenut
    replied
    I did try this for a while. Over time, I really can't say the messages were reduced very much.

    Leave a comment:


  • joegr
    replied
    Originally posted by rschein View Post
    Where's the debug trace?
    In the Debug Logs sub directory off of the main HomeSeer directory.

    Leave a comment:


  • rschein
    replied
    Where's the debug trace? Tried that:
    11/6/2011 16:48:46 System Current debug events set: Z-Wave 11/6/2011 4:48:48 PM Device Update Device: zzzsystem Garage Motion Battery Battery Level 90%11/6/2011 16:49:13 Warning Aborting Z-Wave send, taking too long to send command to node 17 waited 6 seconds11/6/2011 16:49:14 Info Send abort status received.11/6/2011 16:49:14 Warning No response from Z-Wave device at node 1711/6/2011 16:49:14 ZWave Thermostats Aborting poll of this thermostat due to and error retrieving the temperature. Node: 1711/6/2011 16:49:20 Warning Aborting Z-Wave send, taking too long to send command to node 17 waited 6 seconds11/6/2011 16:49:20 Info Send abort status received.11/6/2011 16:49:20 Warning No response from Z-Wave device at node 1711/6/2011 16:49:26 Warning Aborting Z-Wave send, taking too long to send command to node 17 waited 6 seconds11/6/2011 16:49:27 Info Send abort status received.11/6/2011 16:49:27 Warning No response from Z-Wave device at node 1711/6/2011 16:49:33 Warning Aborting Z-Wave send, taking too long to send command to node 17 waited 6 seconds11/6/2011 16:49:34 Info Send abort status received.11/6/2011 16:49:34 Warning No response from Z-Wave device at node 1711/6/2011 16:49:40 Warning Aborting Z-Wave send, taking too long to send command to node 17 waited 6 seconds11/6/2011 16:49:41 Info Send abort status received.11/6/2011 16:49:41 Warning No response from Z-Wave device at node 17


    Attached Files

    Leave a comment:

Working...
X