Hang Up On Caller

[Pete]

But then you've confirmed your number to them.

Not really if you change your outbound calling CID via an outbound call with W2C box. (really NOT legal though but the telemarketers are starting to do this).

[Monk]

Thanks again Wadenut / Pete. Ater allowing HS to reinit the modem by changing something in the settings file it will work exactly one time. Then I can look at the log & see that it supposedly reset the modem OK, but it only works once. The next call will not show CID info @ all.
Too much time on this so am going to put it away .

I have changed a lot of settings about / deleted/recreated my HSPhone.ini and don't remember all of the things I did.

Restoring my yesterday's Acronis image so I don't have to worry that I left something awry.

[Wadenut]

That's really odd.
I wonder... W2C drivers?

[Monk]

Wow

The "Drivers Information" is really verbose! I havent done any driver install since 1/15/2012 when I began using the W2C.
Can't say that I've had any issues with it. Until now that is - cannot make it hangup properly.

Begining to think about using the Snevl script.



========================================

Way2call Drivers Information:
Package Version: 2.01.16.1 32bit
OS version: 6.1.7601 Service Pack 1
Device Information:
1. Hi-Phone Desktop USB 003484
Firmware Version: 4.02.07
P/N: HD00USGR01
S/N: 1011-07-003484

Software Components:
File: w2cUSBM.dll
Description: Way2call Multiple Hi-Phone Devices DLL
Version: 1.3.7.0
Build: b004
File: ScTspML.tsp
Description: Way2call Multiple Hi-Phone Devices TSP
Version: 2.01.16
Build: 0
File: w2cMultiOcx.ocx
Description: Way2call Multiple Hi-Phone Devices OCX
Version: 1.0.0.4
Build: 0
File: TestWiz.exe
Description: Way2call Multiple Hi-Phone Devices Test Wizard
Version: 2.00.34
Build: 0
File: w2cMdSound.exe
Description: Way2call Multiple Devices As Sound Cards
Version: 1.0.0.7
Build: 0
File: scwiz32.exe
Description: Way2Call Multiple Hi-Phone Devices PBX Wizard
Version: 2.00.34
Build: 0
File: w2cTspSetup.exe
Description: Way2call TAPI Setup
Version: 1.0.0.2
Build: 0
File: \drivers\ScIPTsa.sys
Not required - For RS232 devices.
File: w2cRS232Wave.drv
Not required - For RS232 devices.
File: w2cUsb.dll
Description: Hi-Phone User Mode Device Driver
Version: 2.0.9.2
Build: b0001
File: ml_setup.exe
Description: Way2call Multiple Hi-Phone Devices Drivers installer
Version: 2.0.0.43
Build: b001
File: w2cMultiInfo.exe
Description: Way2call drivers infromation
Version: 1.0.0.4
Build: 0

Audio IN devices:
0. Microphone (Hi-Phone Desktop US
1. Microphone (USB PnP Sound Devic
2. Microphone (Hi-Phone Desktop US
Audio OUT devices:
0. Speakers (Realtek High Definiti
1. Speakers (Hi-Phone Desktop USB)
2. Speakers (USB PnP Sound Device
3. Realtek Digital Output (Realtek

[Pete]

I use the SnevlCID script and it works fine. Do my stuff on the side.

I did have an issue with the legacy included with HSPhone W2C drivers and my MS Updates. The older W2C drivers that leave a status icon up were actually preventing the MS Updates; hanging during the updates. The new drivers do not utilize the same DLLs and do not have the status icon. I also never touched the firmware in my W2C box as it worked just fine. There is also an additional diagnostic testing W2C program that I installed that lets you get really granular with the W2C stuff.

[joegr]

- Do you actually get the caller ID?
- Try also, Answer this caller after number of rings = 0
I know I worked a lot on this but it was years ago.

Actually, I found that I had to check "Answer this caller after number of rings = 1" to get it to work. Zero wouldn't work for me after some update version of Homeseer. (I swear it worked before that.)