Announcement
Collapse
No announcement yet.
Original Plugin for Shelly devices - Intro / Config / Screenshots [No MQTT]
Collapse
This is a sticky topic.
X
X
-
Originally posted by alexbk66 View Post
Should be fixed in ver 3.0.0.27 (attached, as developer portal is still f###)
Hope the dev portal is sorted soon. Is there a way of turning off all the entries to the log? All the log check boxes are un-ticked for the device on the settings page.
Comment
-
Originally posted by santoal View PostPerfect. Works a treat.
Is there a way of turning off all the entries to the log? All the log check boxes are un-ticked for the device on the settings page.
And when I get my Dimmers - I will also sort out config page.
BTW, can you please paste the config screenshot?
Comment
-
Just a few things to note on the dimmer below. Having an issue where Alexa is having an issue. Could be the following:
1) Control Use for the slider should be set to Dim
2) The scale perhaps need to be 1-99
3) Last - Control use set to "On Alternate"
4) Property set to "Is Dimmable" - not sure this is required but notice all the z-wave devices have this set.
I would integrate directly with Alexa but someone forgot about adding Australia as a region for the Shelley skill.
On a non related matter, my Dimmer is now plumbed in. It turns off after 10 seconds or so when set to 100% brightness. There are 8 Halogen down lights so it may be drawing to much power. It would be helpful to see temperature and problem status somewhere. Works fine when set to 50% dimming.
Thanks!
Comment
-
Originally posted by santoal View PostJust a few things to note on the dimmer below. Having an issue where Alexa is having an issue. Could be the following:
1) Control Use for the slider should be set to Dim
2) The scale perhaps need to be 1-99
3) Last - Control use set to "On Alternate"
4) Property set to "Is Dimmable" - not sure this is required but notice all the z-wave devices have this set.
I would integrate directly with Alexa but someone forgot about adding Australia as a region for the Shelley skill.
The Dimmer does have temperature reading, so I will add the Temperature device. In the mean time you should be able to see the temperature on the Dimmer config screen under Tmp: tC
Originally posted by santoal View PostOn a non related matter, my Dimmer is now plumbed in. It turns off after 10 seconds or so when set to 100% brightness. There are 8 Halogen down lights so it may be drawing to much power. It would be helpful to see temperature and problem status somewhere. Works fine when set to 50% dimming.
Comment
-
Originally posted by santoal View Post1) Control Use for the slider should be set to Dim
2) The scale perhaps need to be 1-99
3) Last - Control use set to "On Alternate"
4) Property set to "Is Dimmable" - not sure this is required but notice all the z-wave devices have this set.
Except for the scale - I did set max to 99 initially, but then somebody complained that brightness should go to 100, which probably makes sense. You can change it yourself on "Status Graphic" config page.
Also I set "Is Light" option. And added Temperature device. Give it a try.
Comment
-
Originally posted by alexbk66 View Post
Ver 3.0.0.33 in BETA - changed Dimmer settings as described above.
Except for the scale - I did set max to 99 initially, but then somebody complained that brightness should go to 100, which probably makes sense. You can change it yourself on "Status Graphic" config page.
Also I set "Is Light" option. And added Temperature device. Give it a try.
Looks like it's a HS3 or Alexa issue. I have the same problem with all my other dimmers where I get the "waiting for Homeseer" message. I'll need to raise a ticket.
Comment
-
Originally posted by santoal View PostLooks like it's a HS3 or Alexa issue. I have the same problem with all my other dimmers where I get the "waiting for Homeseer" message. I'll need to raise a ticket.
Comment
-
Hi
I've noticed the logging is automatically re-activated after a period of time... I found this in the log:Dec-27 12:12:42 PM AK Shelly [815]: shellyswitch25 (SHSW-25): Execute cmd: status Dec-27 12:12:40 PM AK Shelly ERROR [815]: shellyswitch25 (SHSW-25): [SHSW-25] BA6DDC (192.168.1.215): Execute 'status': Status: 'TimedOut' Error: 'The request was aborted: The operation has timed out.' response: '' code: '0/' 'Timeout' Diasabling and enabling the plug-in resets and works fine againDec-27 10:14:20 AM AK Shelly Locator.Zeroconf.DeviceLocator: ResolverListener ServiceLost: shellyswitch25-BA6DDC:
I have manually changed the IP addresses on the config page for the devices to reflect changes I made on DHCP server. Does this upset things? Seems to work great most of the time.
Cheers
Comment
-
Originally posted by santoal View PostI've noticed the logging is automatically re-activated after a period of time... Diasabling and enabling the plug-in resets and works fine again
Originally posted by santoal View PostI have manually changed the IP addresses on the config page for the devices to reflect changes I made on DHCP server. Does this upset things? Seems to work great most of the time.
Comment
Comment