Mark,
I am having an issue with the plug-in not recognizing the PLM. I have two HomeTrollers - a Zee S2 and a new HT PI G1. This started with the Zee S2 loosing connection to the PLM so I expected it was time for a new one. I picked up a new one and the same issue - "check the interfance and enter port info". Expecting the Zee S2 had a USB port driver failure, or other, it was a good excuse to get a new HT Pi. Loaded CM15A and Insteon 3.0.7.1 on the HTPi, configured the 2413U ID (tried with both the old and the new 2413U) same issue - I end up with the Insteon Plug in stating again WARNING: Please check the Interface and enter the Interface Port information on the Config page and restart HS.
3.0.7.1
and the CM15A has -
CRITICAL: Cannot start mochad! Check HS log for details.
3.0.0.8
The same as experienced with the Zee S2. Granted its been some time since I dabbled with the HS system, but I must be missing something basic. Thoughts? Log attached.
Allen
Date/time=8/4/2021 12:23:17 AM EDT
Version=HomeSeer HS4 Pi Hub G1 Edition 4.1.18.0 (Linux)
MONO Version=Mono JIT compiler version 6.12.0.122 (tarball Mon Feb 22 17:44:05 UTC 2021)
License=Registered
Confguration File=/usr/local/HomeSeer/Data/HomeSeerData.json
Uptime=0 Days 5 Hours 5 Minutes 59 Seconds
Lan IP=10.1.10.172 (HTPiHubG1v2)
Device Count=2
Event Count=0
Plugins Enabled=Z-Wave:,Z-Wave GUI:,CM15A:,Insteon:
Modules/Threads=81 Modules, 50 Threads
Available Threads=399
HomeSeer Memory Used=109 Mbytes
Plugins Installed=CM15A 3.0.0.8,Insteon 3.0.7.1,Z-Wave 3.0.4.0,Z-Wave GUI 0.7.0.1
Disk Size=14.75GB
I am having an issue with the plug-in not recognizing the PLM. I have two HomeTrollers - a Zee S2 and a new HT PI G1. This started with the Zee S2 loosing connection to the PLM so I expected it was time for a new one. I picked up a new one and the same issue - "check the interfance and enter port info". Expecting the Zee S2 had a USB port driver failure, or other, it was a good excuse to get a new HT Pi. Loaded CM15A and Insteon 3.0.7.1 on the HTPi, configured the 2413U ID (tried with both the old and the new 2413U) same issue - I end up with the Insteon Plug in stating again WARNING: Please check the Interface and enter the Interface Port information on the Config page and restart HS.
3.0.7.1
and the CM15A has -
CRITICAL: Cannot start mochad! Check HS log for details.
3.0.0.8
The same as experienced with the Zee S2. Granted its been some time since I dabbled with the HS system, but I must be missing something basic. Thoughts? Log attached.
Allen
Date/time=8/4/2021 12:23:17 AM EDT
Version=HomeSeer HS4 Pi Hub G1 Edition 4.1.18.0 (Linux)
MONO Version=Mono JIT compiler version 6.12.0.122 (tarball Mon Feb 22 17:44:05 UTC 2021)
License=Registered
Confguration File=/usr/local/HomeSeer/Data/HomeSeerData.json
Uptime=0 Days 5 Hours 5 Minutes 59 Seconds
Lan IP=10.1.10.172 (HTPiHubG1v2)
Device Count=2
Event Count=0
Plugins Enabled=Z-Wave:,Z-Wave GUI:,CM15A:,Insteon:
Modules/Threads=81 Modules, 50 Threads
Available Threads=399
HomeSeer Memory Used=109 Mbytes
Plugins Installed=CM15A 3.0.0.8,Insteon 3.0.7.1,Z-Wave 3.0.4.0,Z-Wave GUI 0.7.0.1
Disk Size=14.75GB
Comment