Hi - I'm trying the newest build of Windows 10 Preview. I know that the OS is probaboy not supported but I thought I would post this issue in case its been seen before. I have a PLM that I have been successfully using in Windows 8. I plugged it in to my windows 10 box. Device manager recognizes it and assigns it to Com 3. I have plugged and un-plugged it to verify the port address.
When I enable the plugin, I get a message that the configuration needs to be updated and HS3 restarted. I have done so and verified that the insteon.ini has been written to. Restarting HS3 produces the same result. Here is the log information:
Insteon Plug-in Error Log Generated 12/19/2014 1:02:00 PM
-----------*Error Message*----------------
Error: Forced error / log generation -- 12/19/2014 1:02:00 PM
--------*Initialization Log*--------------
12/19/2014 1:01:36 PM - Host System: xxx.xxx.xxx.xxx (xxxxx) 3.0.0.97
12/19/2014 1:01:36 PM - Plugin: HSPI_Insteon.DLL - v3.0.5.10
12/19/2014 1:01:36 PM - Insteon Support library (Insteon.dll) version: 1.0.5.10
12/19/2014 1:01:36 PM - RegisterCallback Completed
12/19/2014 1:01:36 PM - Enter InitIO
12/19/2014 1:01:36 PM - Enter InitPlugin
12/19/2014 1:01:36 PM - Global initialization of plug-in required, starting up.
12/19/2014 1:01:36 PM - Initializing Insteon hardware interface...
12/19/2014 1:01:36 PM - In ProcessRawReceiveThread
12/19/2014 1:01:36 PM - Initializing Interface...
12/19/2014 1:01:36 PM - In PLMBuffer_ProcessBufferThread
12/19/2014 1:01:36 PM - Insteon hardware interface initialization failed.
12/19/2014 1:01:36 PM - Exit InitIO
-----------*Pre-Error Log*----------------
12/19/2014 1:01:36 PM - Please visit the plugin configuration page, and enter a valid port, then restart HS.
12/19/2014 1:02:00 PM - ***:Forced error / log generation
--------*End Pre-Error Log*--------------
--------*Start C:\Program Files (x86)\HomeSeer HS3\Config\Insteon.ini*--------------
[Config]
MaxHops=2
NumRetries=5
WaitTimeout=3
DetailedLog=1
UseLocation2=0
DoCleanups=1
DisablePolling=0
X10Enabled=0
SortDeviceLinks=0
InterfacePort=3
--------*End C:\Program Files (x86)\HomeSeer HS3\Config\Insteon.ini*--------------
Any help would be appreciated.
When I enable the plugin, I get a message that the configuration needs to be updated and HS3 restarted. I have done so and verified that the insteon.ini has been written to. Restarting HS3 produces the same result. Here is the log information:
Insteon Plug-in Error Log Generated 12/19/2014 1:02:00 PM
-----------*Error Message*----------------
Error: Forced error / log generation -- 12/19/2014 1:02:00 PM
--------*Initialization Log*--------------
12/19/2014 1:01:36 PM - Host System: xxx.xxx.xxx.xxx (xxxxx) 3.0.0.97
12/19/2014 1:01:36 PM - Plugin: HSPI_Insteon.DLL - v3.0.5.10
12/19/2014 1:01:36 PM - Insteon Support library (Insteon.dll) version: 1.0.5.10
12/19/2014 1:01:36 PM - RegisterCallback Completed
12/19/2014 1:01:36 PM - Enter InitIO
12/19/2014 1:01:36 PM - Enter InitPlugin
12/19/2014 1:01:36 PM - Global initialization of plug-in required, starting up.
12/19/2014 1:01:36 PM - Initializing Insteon hardware interface...
12/19/2014 1:01:36 PM - In ProcessRawReceiveThread
12/19/2014 1:01:36 PM - Initializing Interface...
12/19/2014 1:01:36 PM - In PLMBuffer_ProcessBufferThread
12/19/2014 1:01:36 PM - Insteon hardware interface initialization failed.
12/19/2014 1:01:36 PM - Exit InitIO
-----------*Pre-Error Log*----------------
12/19/2014 1:01:36 PM - Please visit the plugin configuration page, and enter a valid port, then restart HS.
12/19/2014 1:02:00 PM - ***:Forced error / log generation
--------*End Pre-Error Log*--------------
--------*Start C:\Program Files (x86)\HomeSeer HS3\Config\Insteon.ini*--------------
[Config]
MaxHops=2
NumRetries=5
WaitTimeout=3
DetailedLog=1
UseLocation2=0
DoCleanups=1
DisablePolling=0
X10Enabled=0
SortDeviceLinks=0
InterfacePort=3
--------*End C:\Program Files (x86)\HomeSeer HS3\Config\Insteon.ini*--------------
Any help would be appreciated.
Comment