This morning JowiHue stopped working. I can control everything Z-Wave. And I can control a Zigbee lamp if I do it in deCONZ.
I thought of starting debug logging, but it seems not to be available. In "Configuration" there is nothing but a message "Plugin is not in ready state yet, bridge unreachable?"
There is connection between them. I started a browser on the Raspberry that runs deCONZ and it would show the Homeseer page.
The log spits out messages: "Warning: JowiHue Plugin is not yet in ready state. Command not executed, please resend after initialisation finished". The last messages from JowiHue before this are these:
I use 2 Raspbery PI. One for deCONZ and the other for Homeseer.
Both were just rebooted (nicely telling them to do it) to see if that would help. It did not.
Here is what it says about itself just now:
Current Date/Time: 11.10.2019 11.25.38
HomeSeer Version: HS3 ZEE S2 Edition 3.0.0.435
Linux version: Linux HomeTrollerZeeS2V2 4.1.19-v7+ #858 SMP Tue Mar 15 15:56:00 GMT 2016 armv7l GNU/Linux System Uptime: 0 Days 1 Hour 21 Minutes 38 Seconds
IP Address: 192.168.1.31
Number of Devices: 307
Number of Events: 85
Available Threads: 394
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed:
Enabled Plug-Ins
2.1.0.5: JowiHue
3.0.1.252: Z-Wave
Regards
Einar Sjaavik
I thought of starting debug logging, but it seems not to be available. In "Configuration" there is nothing but a message "Plugin is not in ready state yet, bridge unreachable?"
There is connection between them. I started a browser on the Raspberry that runs deCONZ and it would show the Homeseer page.
The log spits out messages: "Warning: JowiHue Plugin is not yet in ready state. Command not executed, please resend after initialisation finished". The last messages from JowiHue before this are these:
okt-11 10.05.23 | JowiHue | Refresh bridge DeConz set to 45 seconds after establishing direct connection |
okt-11 10.05.22 | JowiHue | socket opened for DeConz on 192.168.1.32:443 |
okt-11 10.05.15 | JowiHue | Error: (InitPlugin):Start:Collection was modified; enumeration operation might not execute. |
okt-11 10.04.53 | Z-Wave | Starting Z-Wave Polling for Network D10214E0... |
okt-11 10.04.45 | JowiHue | * Connected to bridge DeConz at 192.168.1.32:80 |
okt-11 10.04.31 | Z-Wave | ************************************************************ ******************* |
okt-11 10.04.31 | Z-Wave | STARTUP COMPLETE: All configured interfaces were successfully initialized. |
okt-11 10.04.31 | Z-Wave | ************************************************************ ******************* |
Both were just rebooted (nicely telling them to do it) to see if that would help. It did not.
Here is what it says about itself just now:
Current Date/Time: 11.10.2019 11.25.38
HomeSeer Version: HS3 ZEE S2 Edition 3.0.0.435
Linux version: Linux HomeTrollerZeeS2V2 4.1.19-v7+ #858 SMP Tue Mar 15 15:56:00 GMT 2016 armv7l GNU/Linux System Uptime: 0 Days 1 Hour 21 Minutes 38 Seconds
IP Address: 192.168.1.31
Number of Devices: 307
Number of Events: 85
Available Threads: 394
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed:
Enabled Plug-Ins
2.1.0.5: JowiHue
3.0.1.252: Z-Wave
Regards
Einar Sjaavik
Comment