Magic Color Controllers

[fuzzysb]

These should just be set to bulb i think

[RK15]

these bulbs stop changings colors https://www.amazon.com/gp/product/B0...A2BM80QFXW4SS3
i have then set for BULBRGBWARNWHITECOOLWHITE any ideas.

[fuzzysb]

Yes I get the same issue. Simply put we attempted to send data and recieve a response. But the device failed to send any response. There's not much I can do other than downgrade it from an error to a debug log entry. These devices aren't the best bit they do work. But they don't always respond and you need multiple attempts to achieve a response

[RK15]

I keep getting these errors in log

[RK15]

is there a way to link 2 bulbs together so u only need to change 1 bulb color and the rest will change.

[RK15]

have mode set for bulb and color sliders are working but if I turn on warn white it goes on but if I try to change the colors the bulb blinks and stay warn white I have to move warn white slider to 0 then change color and i have no cool white

[fuzzysb]

based on what you stated that the following commands worked.

31 FF 00 00 00 F0 0F 2F set red
31 00 00 00 FF 0F 0F 4E set white

I have confirmed that when you have your device set to bulb, you 100% do actually send the command as per the above red command.

I have release v1.0.0.302 that now includes a BulbRgbWarmwhiteCoolwhite, as i can see from other sources that there is now a need for that device type also. but i dont think this is for your bulb. but i also have introduced a delay between the colour and white commands in case that was causing issues. and i also have made it skip the white set if its current value is 0

for testing can you ensure that in the Magic home app you set all the whites level to off and the red to about half. then start the plugin and wait for discovery, once that is finished, just set the red slider to Full, does this increase the brightness of the Red to Full? it 100% should do in my testing as it sends the exact red command above.

after which try different combinations of colour or whites, or colour and whites. let me know your results

[fuzzysb]

Ok. It's late and I've finished for the night here butbut ba on those commands you've confirmed work. I need to recheck the logic as I believed this is what I was sending in the last beta. But will 100% check tomorrow morning. And let you know

[RK15]

I think by looking at the app the cool white is only red,blue,green on full

[RK15]

31 FF 00 00 00 F0 0F 2F set red
31 00 00 00 FF 0F 0F 4E set white

[fuzzysb]

RK15 ok i am going to need you to send some command with Packet Sender. sorry to be a pain

if works should set red to 100%
packetsender -xtw 500 <bulb IP> 5577 "31 FF 00 00 00 00 F0 0F 2F"

if works should set red to 100%
packetsender -xtw 500 <bulb IP> 5577 "31 FF 00 00 00 F0 0F 2F"

if works should set warm white to 100%
packetsender -xtw 500 <bulb IP> 5577 "31 00 00 00 FF 00 0F 0F 4E"

if works should set cool white to 100%
packetsender -xtw 500 <bulb IP> 5577 "31 00 00 00 00 FF 0F 0F 4E"

if works should set warm white to 100%
packetsender -xtw 500 <bulb IP> 5577 "31 00 00 00 FF 0F 0F 4E"

can you just tell me if any work, i suspect both 1, 3, 4 should work for you, if so will require one more bulb type to be created in app if none work then i think the v8 firmware will be offering something else additional and i will have to see if i can purchase a device. but i don't have the same available for same in the UK. I do have however

https://www.amazon.co.uk/Equivalent-...agic+Home+Bulb

which hopefully with a later version i may hit the same issue. but if you can let me know the results above before i purchase a bulb i don't need

[RK15]

updated. have mode set to bulb and if I move the sliders the bulb blinks but dose not change color and the coloru box dose not change

[fuzzysb]

RK15 ah ok that information about the warm white slider is very important.

I have just posted new update v1.0.0.297 Beta to the beta section of the updater, please update and let me know how you get on. does that fix the behaviour of your colour setting.

[RK15]

also noticed that the coloru box dose not change if u move the red,blue, green slders, I have mode set to blub or in

RgbWarmwhiteCoolwhite

[RK15]

if I set to

RgbWarmwhiteCoolwhite only can turn blub on an off no sliders work, and no error in logs. if I set it to bulb

Warm White slider works