Announcement

Collapse
No announcement yet.

help for a newbie.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    help for a newbie.

    what does this tell you , other than the obvious?
    May-12 4:55:05 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 20 [07140114FF30A1] to PIM -- timed out 5 times -- discarding message
    May-12 4:54:59 PM Device Control Device: Breakfast Room Breakfast Table to On (100) by/from: CAPI Control Handler
    May-12 4:54:42 PM Device Control Device: Breakfast Room Breakfast Table to On (100)
    May-12 4:54:20 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 19 [07140113FF30A2] to PIM -- timed out 5 times -- discarding message
    May-12 4:53:35 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 18 [07140112FF30A3] to PIM -- timed out 5 times -- discarding message
    May-12 4:53:14 PM Device Control Device: Breakfast Room Breakfast Table to On (100) by/from: CAPI Control Handler
    May-12 4:53:05 PM Device Control Device: Great Room Fireplace Lights to On (100) by/from: CAPI Control Handler
    May-12 4:52:50 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 17 [07140111FF30A4] to PIM -- timed out 5 times -- discarding message
    May-12 4:52:05 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 16 [07140110FF30A5] to PIM -- timed out 5 times -- discarding message
    May-12 4:51:20 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 15 [0714010FFF30A6] to PIM -- timed out 5 times -- discarding message
    May-12 4:50:35 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 14 [0714010EFF30A7] to PIM -- timed out 5 times -- discarding message

    #2
    Most likely is that the plugin cannot access the PIM.
    What kind of PIM is it? Have you close UPstart before starting the plugin?

    Comment


      #3
      It is a pcs powerline pim. yes, i thought i did. i';ll try it again. i am not getting the error messages like i was before,. but the lights still arent lighting.
      May-12 5:06:39 PM Device Control Device: Great Room Fireplace Lights to On (100) by/from: CAPI Control Handler
      May-12 5:06:34 PM Device Control Device: Great Room Fireplace Lights to On (100) by/from: CAPI Control Handler
      May-12 5:06:28 PM Device Control Device: Breakfast Room Breakfast Table to Blink (-5) by/from: CAPI Control Handler
      May-12 5:06:23 PM Device Control Device: Breakfast Room Breakfast Table to Blink (-5) by/from: CAPI Control Handler
      May-12 5:06:18 PM Device Control Device: Breakfast Room Breakfast Table to Dim 99% (99) by/from: CAPI Control Handler
      May-12 5:06:13 PM Device Control Device: Breakfast Room Breakfast Table to On (100) by/from: CAPI Control Handler
      May-12 5:06:08 PM Device Control Device: Breakfast Room Breakfast Table to On (100) by/from: CAPI Control Handler
      May-12 5:06:00 PM Energy DB Info All energy database compacting routines completed.
      May-12 5:06:00 PM Energy DB Info No Records. Vacuuming database to condense.
      May-12 5:06:00 PM Energy DB Info Energy database compaction initiated.
      May-12 5:05:28 PM Device Control Device: Great Room Rear Floods to On (100) by/from: CAPI Control Handler
      May-12 5:03:18 PM Device Control Device: Great Room Rear Floods to On (100) by/from: CAPI Control Handler

      Comment


        #4
        what mode does the pim need to be in when i turn off the upb? I left it in pulse mode

        Comment


          #5
          do i disconnect the pim from upb when shutting it down?

          Comment


            #6
            Message/Source
            May-12 5:11:34 PM Device Control Device: Great Room Rear Floods to On (100) by/from: CAPI Control Handler
            May-12 5:11:29 PM UPBSpud INFO Checking HS Devices Completed
            May-12 5:11:17 PM UPBSpud INFO Checking HS Devices Started
            May-12 5:11:17 PM UPBSpud INFO Import of UPStart file completed
            May-12 5:11:17 PM Plug-In Finished initializing plug-in UPBSpud
            May-12 5:11:17 PM Starting Plug-In UPBSpud loaded in 516 milliseconds
            May-12 5:11:17 PM UPBSpud INFO Import of UPStart file started
            May-12 5:11:17 PM Starting Plug-In Plugin UPBSpud started successfully in 61 milliseconds
            May-12 5:11:17 PM UPBSpud INFO UPBSpud version 3.0.0.50
            May-12 5:11:17 PM Starting Plug-In Initializing plugin UPBSpud ...
            May-12 5:11:17 PM Info Plugin UPBSpud has connected. IP:127.0.0.1:51542
            May-12 5:11:03 PM UPBSpud INFO Shutting Down UPBSpud plugin
            May-12 5:11:03 PM Plug-In Shutting down Plug-In: UPBSpud

            Comment


              #7
              now i got an error message
              May-12 5:12:19 PM UPBSpud ERROR PIM_SEND:: ERROR: Unable to send message ID 1 [0814011CFF226442] to PIM -- timed out 5 times

              Comment


                #8
                does this look normal
                Status Floor Room Name Last Change Control
                Off
                Great Room Rear Floods On Off Blink Last Level
                Off
                Great Room Fireplace Lights On Off Blink Last Level
                Off
                Foyer Front Floods On Off Blink Last Level
                Off
                Foyer Foyer Light On Off Blink Last Level
                Off
                Dining Room Dining Lights On Off Blink Last Level
                Off
                Breakfast Room Breakfast Table On Off Blink Last Level

                Comment


                  #9
                  the pim works when in upb mode. what am i missing

                  Comment


                    #10
                    make sure you have entered the correct COM port in the Config page
                    are you on Windows or Linux?

                    from the config page set the log level to Debug to get more information

                    Comment


                      #11
                      copuldnt confirm com port in upb, so changed it form com3 to com1. using windows. web interface. how do i set to debug mode

                      Comment


                        #12
                        at the bottom of the Config page, the same page you use to enter the COM port, there is "log level" field, set it to Debug

                        also, not sure it is important but I think the com port should be upper case COM3 instead of com3

                        Comment


                          #13
                          Originally posted by rabjab12 View Post
                          copuldnt confirm com port in upb, so changed it form com3 to com1. using windows. web interface.
                          To see your COM ports: In File Explorer (on the HS PC) right click on 'This PC', then select 'Manage'. That will bring up the Device Manager. Select 'Ports (Com & LPT)' to get a list of ports in use. I've noted my UPB port below with the red mark.

                          Click image for larger version

Name:	port.PNG
Views:	212
Size:	62.9 KB
ID:	1304409

                          Mike____________________________________________________________ __________________
                          HS3 Pro Edition 3.0.0.548, NUC i3

                          HW: Stargate | NX8e | CAV6.6 | Squeezebox | PCS | WGL 800RF | RFXCOM | Vantage Pro | Green-Eye | Edgeport/8 | Way2Call | Ecobee3 | EtherRain | Ubiquiti

                          Comment


                            #14
                            here is what i am seeing

                            Comment


                              #15
                              i have the upb pim plugged into a usb port as well as a keyboard and mouse

                              Comment

                              Working...
                              X