Announcement

Collapse
No announcement yet.

pH and ORP devices and hide buttons

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • DonMor
    replied
    When I activate the:
    Select the option below to create pH and ORP devices if you have the Sense and Dispense unit installed:
    pH and ORP Devices Enable

    I got the:
    Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.
    in the log.

    Can you correct this or did I do something wrong?

    I'm running the version : 3.0.2.0

    Leave a comment:


  • Mister2t
    replied
    Hi Mats,

    I think it was because the plugin was not expecting to see the "(off)" or "(on)". I made a tweak and added the option to create the "Cell Temp" device you requested.

    Give it a shot and let me know how it goes.

    Thanks,

    Mike
    Attached Files

    Leave a comment:


  • Mats2
    replied

    Leave a comment:


  • Mats2
    replied
    Hi,

    With this version, I do get values in the devices but there are still some errors:


    This is from the thread:






    When scrolling to the show the value in the "Default Menu", Screen says: "pH 7.6 ORP 645 mV"

    May-18 10:50:42 PM AquaConnect workingstring = 645 mV
    May-18 10:50:42 PM AquaConnect detected pH/ORP update
    May-18 10:50:42 PM AquaConnect workingstring = pH 7.6
    May-18 10:50:42 PM AquaConnect workingstring = 7.6
    May-18 10:50:40 PM AquaConnect workingstring = pH 7.6
    May-18 10:50:40 PM AquaConnect workingstring = 7.6
    May-18 10:50:40 PM AquaConnect workingstring = 645 mV
    May-18 10:50:40 PM AquaConnect detected pH/ORP update
    May-18 10:50:38 PM AquaConnect workingstring = 7.6
    May-18 10:50:38 PM AquaConnect workingstring = 645 mV
    May-18 10:50:38 PM AquaConnect detected pH/ORP update
    May-18 10:50:38 PM AquaConnect workingstring = pH 7.6
    May-18 10:50:36 PM AquaConnect workingstring = 7.6
    May-18 10:50:36 PM AquaConnect workingstring = 645 mV
    May-18 10:50:36 PM AquaConnect detected pH/ORP update
    May-18 10:50:36 PM AquaConnect workingstring = pH 7.6
    May-18 10:50:34 PM AquaConnect workingstring = 645 mV
    May-18 10:50:34 PM AquaConnect detected pH/ORP update




    When scrolling to the show the value in the "Diagnostic Menu", Screen says: "pH 7.6 (Off)ORP 645 mV (Off)" (have not seen the "(Off) " earlier).

    May-18 10:53:34 PM AquaConnect Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.
    May-18 10:53:34 PM AquaConnect detected pH/ORP update
    May-18 10:53:34 PM AquaConnect workingstring =
    May-18 10:53:32 PM AquaConnect Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.
    May-18 10:53:32 PM AquaConnect detected pH/ORP update
    May-18 10:53:32 PM AquaConnect workingstring =
    May-18 10:53:28 PM AquaConnect Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.
    May-18 10:53:28 PM AquaConnect detected pH/ORP update
    May-18 10:53:28 PM AquaConnect workingstring =
    May-18 10:53:26 PM AquaConnect detected pH/ORP update
    May-18 10:53:26 PM AquaConnect workingstring =
    May-18 10:53:26 PM AquaConnect Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.
    May-18 10:53:24 PM AquaConnect detected pH/ORP update


    thanks
    Mats

    Leave a comment:


  • Mister2t
    replied
    Thanks Mats...that's the problem with me not having sense and dispense...can't actually test it.

    OK...think I found a bug. But, I added some additional logging just in case. If this version works, I can remove the logging and repost.

    Thanks,

    Mike
    Attached Files

    Leave a comment:


  • Mats2
    replied
    Hi,

    Don't worry about any hijacking, the more the merrier.

    I tried this version and have some problems.
    In the log, I see a lot of these errors:

    Error in ProcessResponse, Argument 'Length' must be greater or equal to zero.


    The other problem is the new devices. I can see the devices for pH and ORP but there are no values filled in?
    I wasn't clear in my initial post but the pH and ORP values are shown at the same time when the display scrolls.:
    "pH 7.6 ORP 640 mV"
    not sure if that could be the cause?


    thanks
    Mats

    Leave a comment:


  • Mister2t
    replied
    Great to hear you are up and running...enjoy the pool!

    Leave a comment:


  • happnatious1
    replied
    You are right about the designer screwing up the display, it looks fine on the client.

    Valve 3 is working properly as well.

    Thanks for all your help and a terrific plugin!

    and my apologies to Mats for high jacking this thread.

    Pool is open!

    Leave a comment:


  • Mister2t
    replied
    Does the aquaconnect control page look correct when looking at it from a browser? If you resize browser you should see the layout change to accommodate smaller widths.

    This may also just be an artifact of the hstouch design interface. Have you tried pushing the hstouch project to your device to actually see what it lookalike on it running?

    Did the valve3 issue get resolved?

    Leave a comment:


  • happnatious1
    replied
    ac.css is there, should that be resizing the webpage in hstouch?

    Leave a comment:


  • Mister2t
    replied
    Also noticed that the latest file I uploaded shows 0 views...which seems to indicate no one has downloaded it yet? Perhaps you uploaded one of the previous versions? Either way...just be sure to use the latest version I posted.

    Leave a comment:


  • Mister2t
    replied
    Very strange...Just tested mine again and everything is working fine? Only thing I can think of there is to completely remove the AquaConnect installation and then install again from uploader. Then replace the HSPI file using the version I uploaded to try again.

    The screenshot you showed seems to indicate that css file is missing. Let me know if ac.css is located in html/css/aquaconnect folder. If it is there, I could send you a teamviewer invite, so I could look at your computer realtime to troubleshoot.

    Either way...I'm sure we will figure it out.

    Thanks,

    Mike

    Leave a comment:


  • happnatious1
    replied
    Valve3 is still there in the new version.

    Great idea on hstouch but I don't seam to be able to get the control page to scale properly. I have to either cut off the top or the bottom.
    Last edited by happnatious1; May 16th, 2015, 02:36 PM.

    Leave a comment:


  • Mister2t
    replied
    Thanks for letting me know about the Valve3 issue. I found a problem in the code. try the attached version.

    On the topic of creating HSTouch screens for the pool controller. In case you were unaware, you can just create a screen that simply displays the AquaConnect control page...it makes your life much easier. Assuming you are happy using that design in your HSTouch.
    Attached Files

    Leave a comment:


  • happnatious1
    replied
    Thanks for the example, I understand the logic now and should be able to create events for all the scenarios that I'm used to. I've only been using the new system for a couple days as I'm starting up my pool for the season and converting to salt but it looks like the research I did over the winter is really paying off. Having full control of my pool through homeseer is awesome!

    I did notice on the new version that even though I have valve3 unchecked it still shows on the control page.

    Next to create HSTouch screens!

    Leave a comment:

Working...
X