Hello,
I have just installed a DSC PC1832 with Envisalink, the plug-in is working great in HS3 but I have one problem:
When I arm partition 1, the keypad arms without any problem but I get the following log entries in HS3 - it basically says that the partition is arm but then 13 seconds later that it failed to arm:
Feb-15 10:07:44 PM EnvisaLink DEBUG PartitionFailedtoArm 1
Feb-15 10:07:31 PM EnvisaLink DEBUG PartitionArmed 11
Feb-15 10:07:31 PM EnvisaLink DEBUG UserClosing 10040
Feb-15 10:07:31 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 8A
Feb-15 10:07:14 PM EnvisaLink DEBUG CommandAcknowledge 000
Feb-15 10:07:14 PM EnvisaLink DEBUG Request: Poll
Feb-15 10:06:52 PM EnvisaLink DEBUG ExitDelayinProgress 1
Feb-15 10:06:51 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 8B
Feb-15 10:06:46 PM EnvisaLink DEBUG CommandAcknowledge 200
Feb-15 10:06:46 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 80
Feb-15 10:06:46 PM EnvisaLink DEBUG Request: CodeSend 1234
Feb-15 10:06:46 PM EnvisaLink DEBUG CodeRequired
Feb-15 10:06:45 PM EnvisaLink DEBUG CommandAcknowledge 031
Feb-15 10:06:45 PM EnvisaLink DEBUG Request: PartitionArmControlStayArm 1
Feb-15 10:06:45 PM Device Control Device: EnvisaLink Partition 1 to Arm Stay (-1000) by/from: CAPI Control Handler
So the system is actually armed on the keypad and when I try to disarm it in HS3, I get the SystemError 023, which means that the system is not armed. However the system is armed but for some reason Envisalink thinks it is not. So I tried to arm it again but that results in SystemError 24. This is the log:
Feb-15 10:08:26 PM EnvisaLink DEBUG SystemError 023
Feb-15 10:08:26 PM EnvisaLink DEBUG Request: PartitionDisarmControl 11234
Feb-15 10:08:26 PM Device Control Device: EnvisaLink Partition 1 to Disarm (-1002) by/from: CAPI Control Handler
Feb-15 10:08:17 PM EnvisaLink DEBUG SystemError 024
Feb-15 10:08:17 PM EnvisaLink DEBUG Request: PartitionArmControlStayArm 1
Feb-15 10:08:17 PM Device Control Device: EnvisaLink Partition 1 to Arm Stay (-1000) by/from: CAPI Control Handler
Feb-15 10:08:08 PM EnvisaLink DEBUG SystemError 023
Feb-15 10:08:08 PM EnvisaLink DEBUG Request: PartitionDisarmControl 11234
Feb-15 10:08:08 PM Device Control Device: EnvisaLink Partition 1 to Disarm (-1002) by/from: CAPI Control Handler
Have I programmed the system wrong?
Thanks,
Guido
I have just installed a DSC PC1832 with Envisalink, the plug-in is working great in HS3 but I have one problem:
When I arm partition 1, the keypad arms without any problem but I get the following log entries in HS3 - it basically says that the partition is arm but then 13 seconds later that it failed to arm:
Feb-15 10:07:44 PM EnvisaLink DEBUG PartitionFailedtoArm 1
Feb-15 10:07:31 PM EnvisaLink DEBUG PartitionArmed 11
Feb-15 10:07:31 PM EnvisaLink DEBUG UserClosing 10040
Feb-15 10:07:31 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 8A
Feb-15 10:07:14 PM EnvisaLink DEBUG CommandAcknowledge 000
Feb-15 10:07:14 PM EnvisaLink DEBUG Request: Poll
Feb-15 10:06:52 PM EnvisaLink DEBUG ExitDelayinProgress 1
Feb-15 10:06:51 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 8B
Feb-15 10:06:46 PM EnvisaLink DEBUG CommandAcknowledge 200
Feb-15 10:06:46 PM EnvisaLink DEBUG KeypadLedStatePartition1Only 80
Feb-15 10:06:46 PM EnvisaLink DEBUG Request: CodeSend 1234
Feb-15 10:06:46 PM EnvisaLink DEBUG CodeRequired
Feb-15 10:06:45 PM EnvisaLink DEBUG CommandAcknowledge 031
Feb-15 10:06:45 PM EnvisaLink DEBUG Request: PartitionArmControlStayArm 1
Feb-15 10:06:45 PM Device Control Device: EnvisaLink Partition 1 to Arm Stay (-1000) by/from: CAPI Control Handler
So the system is actually armed on the keypad and when I try to disarm it in HS3, I get the SystemError 023, which means that the system is not armed. However the system is armed but for some reason Envisalink thinks it is not. So I tried to arm it again but that results in SystemError 24. This is the log:
Feb-15 10:08:26 PM EnvisaLink DEBUG SystemError 023
Feb-15 10:08:26 PM EnvisaLink DEBUG Request: PartitionDisarmControl 11234
Feb-15 10:08:26 PM Device Control Device: EnvisaLink Partition 1 to Disarm (-1002) by/from: CAPI Control Handler
Feb-15 10:08:17 PM EnvisaLink DEBUG SystemError 024
Feb-15 10:08:17 PM EnvisaLink DEBUG Request: PartitionArmControlStayArm 1
Feb-15 10:08:17 PM Device Control Device: EnvisaLink Partition 1 to Arm Stay (-1000) by/from: CAPI Control Handler
Feb-15 10:08:08 PM EnvisaLink DEBUG SystemError 023
Feb-15 10:08:08 PM EnvisaLink DEBUG Request: PartitionDisarmControl 11234
Feb-15 10:08:08 PM Device Control Device: EnvisaLink Partition 1 to Disarm (-1002) by/from: CAPI Control Handler
Have I programmed the system wrong?
Thanks,
Guido
Comment