Clean install error starting

[chrkov]

Ultra,

I am getting the following when starting the plugin on a clean install of HS 2.3.0.19

2/25/2009 8:01:32 PM - UltraM1G Warning - Elk M1 interface is disabled.
2/25/2009 8:01:32 PM - Error - Initializing interface: UltraM1G->Unable to initialize Elk M1 Hardware :Elk M1 interface is disabled.
2/25/2009 8:01:32 PM - Info - Finished initializing plug-in UltraM1G

My old server died completely and I need to get this reloaded as quick as possible.

Thanks

Chris

[Rupp]

Have you enable the plugin via the Setup > Interfaces tab?

[chrkov]

Rupp,

That is what I was getting when I enabled it. But I think I figured it out. I never enabled the plugin before I entered my registration code on it. I deleted the license file, started it and then registered it and it seems to be working now except I keep getting the following now.


2/25/2009 8:18:32 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0800'
2/25/2009 8:18:34 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0800'
2/25/2009 8:18:35 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0800'
2/25/2009 8:18:37 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0900'
2/25/2009 8:18:38 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0900'
2/25/2009 8:18:40 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0900'
2/25/2009 8:18:41 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv1000'
2/25/2009 8:18:43 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv1000'
2/25/2009 8:18:44 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv1000'
2/25/2009 8:19:07 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0100'
2/25/2009 8:19:09 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0100'
2/25/2009 8:19:10 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0100'
2/25/2009 8:19:12 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0200'
2/25/2009 8:19:13 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0200'
2/25/2009 8:19:15 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0200'
2/25/2009 8:19:16 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0300'
2/25/2009 8:19:18 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0300'
2/25/2009 8:19:20 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0300'
2/25/2009 8:19:21 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0400'
2/25/2009 8:19:23 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0400'
2/25/2009 8:19:24 PM - UltraM1G Warning - No response/improper response from Elk M1 to command 'cv0400'

Any ideas on that?


Thanks

Chris

[Ultrajones]

Set the counter value to 0 from the options web page, then restart Homeseer. It sounds like your Elk firmware doesn't support counters.

[chrkov]

That fixed the problem, but my elk panel does support counters. I have two in use now.