Announcement

Collapse
No announcement yet.

Honeywell WiFi Thermostat Release History

Collapse
This topic is closed.
X
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • shill
    replied
    NOTE: All release notes can be found in the official HomeSeer store Release Notes page for this plugin.

    Leave a comment:


  • shill
    replied
    *** Version 1.3.2 *** - 6/1/2018

    • Adjusted logging to prevent output of large HTML components unless LogLevel is set to 7 (TraceHTML, not available in the Options UI).
    • Fixed an issue where the Config page allowed adding a thermostat with a duplicate ID value.
    • Fixed an issue where deleting thermostats from the Config page did not remove all devices.

    Leave a comment:


  • shill
    replied
    *** Version 1.3.1 *** - 5/23/2018

    • Fixed an issue with using the Device Config page to change the Device ID if the original device is no longer present on the TCC portal.

    Leave a comment:


  • shill
    replied
    *** Version 1.3.0 *** - 5/20/2018

    • Reverted to HTTP client for web interactions. This will require mono 4.8 or higher for Linux/Zee users.
    • Add thermostat device ID to log messages wherever known.
    • Improved performance of logging.
    • Changed the tracking of login frequency and added a config-file-only login timeout value (in minutes) for how often the plugin should perform a fresh login (vs assuming the session is still good).

    Leave a comment:


  • shill
    replied
    *** Version 1.2.5 *** - 5/12/2018

    • More login detection fixes.
    • Added logic to detect maintenance downtime and delay the next update for 15 minutes.
    • Added 5 second timeouts for connections.
    • Added additional logging around each web request.
    • Added logic to prevent interactions until the thermostat has had a chance to update.

    Leave a comment:


  • shill
    replied
    *** Version 1.2.4 *** - 5/7/2018

    • Fixed an issue with incorrectly detecting successful logins for systems with only one thermostat.

    Leave a comment:


  • shill
    replied
    *** Version 1.2.3 *** - 5/5/2018

    • Fixed an issue with incorrectly reporting failed logins.
    • Improved logging for failed requests.

    Leave a comment:


  • shill
    replied
    *** Version 1.2.2 *** - 4/30/2018

    • Re-release of the libcurl-based solution to resolve TLS issues for Windows XP and Linux-based users, with additional logging for potential failure areas. (Linux/Zee users make sure you follow the instructions from earlier this month to prepare!)

    Leave a comment:


  • shill
    replied
    *** Version 1.2.1 *** - 2/25/2018

    • Reverted previous change because of user issues with dependencies and other unexplained behaviors.

    Leave a comment:


  • shill
    replied
    *** Version 1.2.0 *** - 2/23/2018

    • Replaced the entire HTTP client with CurlSharp to avoid Mono defects and to provide full TLS support for XP and Linux users.

    Leave a comment:


  • shill
    replied
    *** Version 1.1.13 *** - 2/15/2018

    • Added the ability to change the device ID and name used when registering the thermostat in the plugin on the root Device's config screen.

    Leave a comment:


  • shill
    replied
    *** Version 1.1.12 *** - 10/17/2017

    • Added logic to report Operating Status as Idle when the System Mode is “Off” and the Fan Status is “Idle” to overcome a defect in Honeywell’s JSON data that incorrectly reported the Status as active if it had been at the time the Mode was switched off.
    • Added “Docs” page to Plugin menu with links to local documentation and the support forum.

    Leave a comment:


  • shill
    replied
    *** Version 1.1.11 *** - 7/21/2017

    • Fixed an issue with changing the Cool Setpoint when in “Simulate Auto Mode” in some situations.

    Leave a comment:


  • shill
    replied
    *** Version 1.1.10 *** - 7/11/2017

    • Fixed an issue with the log file not being written properly.
    • Fixed an issue with loading the Newtonsoft DLL with HS3 version 3.0.0.333.

    Leave a comment:


  • shill
    replied
    *** Version 1.1.9 *** - 6/11/2017

    • Fixed an issue where the thermostat would not enter “Simulate Auto Mode” in some situations.

    Leave a comment:

Working...
X