Announcement

Collapse
No announcement yet.

Easy Trigger plug-in - Feature Requests

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • logman
    replied
    Originally posted by Stuart View Post
    Since easytrigger can enable and disable events, is it possible to check the status of and event as a condition (enabled, disabled) ?
    Thanks,
    I had a use case recently where I wished for that capability too. I wanted Event 2 to only fire if Event 1 was disabled and I wanted Event 3 to only fire if Event 1 was enabled.

    --Barry

    Leave a comment:


  • Stuart
    replied
    Since easytrigger can enable and disable events, is it possible to check the status of and event as a condition (enabled, disabled) ?
    Thanks,

    Leave a comment:


  • spud
    replied
    Originally posted by jvm View Post
    Thanks. can you confirm - do these new group functions set all of the standard "ET..." Global Variables to indicate which of the devices in the group caused the trigger to fire?
    correct

    Leave a comment:


  • jvm
    replied
    Thanks. can you confirm - do these new group functions set all of the standard "ET..." Global Variables to indicate which of the devices in the group caused the trigger to fire?

    Leave a comment:


  • rprade
    replied
    Originally posted by logman View Post

    That will work. But it would also work just as well if your Trigger (the "IF") was simply "on" rather than "on for 2 minutes". The Condition "AND IF" can only be true if the virtual switch is on and the wattage indicates the physical dryer has been off for 2 minutes, so the time condition for the Trigger is not necessary.

    I'm not a processor engineer, but I believe using a simple Trigger will also lower the complexity (CPU clocks) of the event by several fold.

    --Barry
    3 things. (1) If you want the trigger to be "Has been On for at least 0 seconds, it will trigger once a second. (2) There is no trigger for being On, only set On, changed to On, On for at least... or On for Exactly... (3) there are virtually no resources used for a trigger, when conditions are not met, so a recurring trigger will only use CPU cycles when the following conditions are ALL true. His trigger of "On for at least 2 minutes" or a recurring trigger will have virtually the same impact on system resources since once 2 minutes has elapsed, it will trigger once a second until the Condition is met.

    Leave a comment:


  • MattL0
    replied
    Thanks spud ! Just updated. No errors.

    That will be a passive test for me since I will have less time in the next weeks. will let you know.

    Leave a comment:


  • spud
    replied
    Originally posted by teladog01 View Post


    spud, any chance these Device triggers will be implemented for Groups? I'd appreciate some commentary either way...

    If there is no plan to implement these triggers for goups, then I will start planning an alternate design for my events. But it they might be implemented in the near future then I will hold out for that since these missing group triggers would dramatically simplify some of the events I'm planning to implement.
    The new triggers/conditions for device groups are in version 3.0.0.68 (available in the beta section of the updater)
    I also did quite a bit of refactoring so let me know if I broke something.

    Click image for larger version

Name:	devicegrouptriggers.png
Views:	206
Size:	53.4 KB
ID:	1325246

    Leave a comment:


  • logman
    replied
    Originally posted by gmitch64 View Post

    Hopefully this will work...

    Click image for larger version

Name:	Capture4.PNG
Views:	167
Size:	28.4 KB
ID:	1325165
    That will work. But it would also work just as well if your Trigger (the "IF") was simply "on" rather than "on for 2 minutes". The Condition "AND IF" can only be true if the virtual switch is on and the wattage indicates the physical dryer has been off for 2 minutes, so the time condition for the Trigger is not necessary.

    I'm not a processor engineer, but I believe using a simple Trigger will also lower the complexity (CPU clocks) of the event by several fold.

    --Barry

    Leave a comment:


  • gmitch64
    replied
    Originally posted by rprade View Post
    Spud does not allow for "At Least" (to prevent runaway Triggers) in Triggers, only "Exactly" He does allow it in Conditions, so set up a recurring Trigger, then use your "At Least:" in a Condition..
    Hopefully this will work...

    Click image for larger version

Name:	Capture4.PNG
Views:	167
Size:	28.4 KB
ID:	1325165

    Leave a comment:


  • rprade
    replied
    Originally posted by gmitch64 View Post
    There are options in EasyTrigger for a devices value has been in the range {X,Y] for exactly... (and NOT been in range). Would it be possible to also add so that a device can be in the range for "at least"... Standard HS allows for the "at least", but only for a single value, not ranges.

    I'm trying to add some automation to my drier and washer, and the ranges work fine, but it doesn't always run when I chose "exactly 2 mins", and I'd like to be able to chose "at least 2 mins" so that it doesn't trigger when the washer and drier are on the low power part of their cycles.


    Thanks

    G
    Spud does not allow for "At Least" (to prevent runaway Triggers) in Triggers, only "Exactly" He does allow it in Conditions, so set up a recurring Trigger, then use your "At Least:" in a Condition..

    Leave a comment:


  • gmitch64
    replied
    There are options in EasyTrigger for a devices value has been in the range {X,Y] for exactly... (and NOT been in range). Would it be possible to also add so that a device can be in the range for "at least"... Standard HS allows for the "at least", but only for a single value, not ranges.

    I'm trying to add some automation to my drier and washer, and the ranges work fine, but it doesn't always run when I chose "exactly 2 mins", and I'd like to be able to chose "at least 2 mins" so that it doesn't trigger when the washer and drier are on the low power part of their cycles.


    Thanks

    G

    Leave a comment:


  • teladog01
    replied
    Originally posted by spud View Post

    Sorry for the lack of response.
    I have them implemented but I need some time to test them a little more. Expect a new beta version in a few days.
    Awesome! Thanks for confirming.

    Leave a comment:


  • spud
    replied
    Originally posted by teladog01 View Post


    spud, any chance these Device triggers will be implemented for Groups? I'd appreciate some commentary either way...

    If there is no plan to implement these triggers for goups, then I will start planning an alternate design for my events. But it they might be implemented in the near future then I will hold out for that since these missing group triggers would dramatically simplify some of the events I'm planning to implement.
    Sorry for the lack of response.
    I have them implemented but I need some time to test them a little more. Expect a new beta version in a few days.

    Leave a comment:


  • teladog01
    replied
    Originally posted by teladog01 View Post
    Hi spud,

    Would be very helpful for all of the triggers in "A Device's Value is..." to be available in the "Any Device's Value in Group is..." triggers. I am particularly interested in the ones highlighted below, but seems maybe they should all be available for groups for the sake of completeness, except maybe the comparison one (not sure how that would work)?

    Thanks for considering...

    Click image for larger version Name:	Screenshot 2019-06-09 13.44.24.png Views:	0 Size:	298.6 KB ID:	1309637Hi

    spud, any chance these Device triggers will be implemented for Groups? I'd appreciate some commentary either way...

    If there is no plan to implement these triggers for goups, then I will start planning an alternate design for my events. But it they might be implemented in the near future then I will hold out for that since these missing group triggers would dramatically simplify some of the events I'm planning to implement.

    Leave a comment:


  • drhtmal
    replied
    Now that I have EasyTrigger working (thanks for all the helpful suggestions) I have a real feature request.

    It would be useful to have some filtering on the device selection dialog. Something like the filtering on the Device Management page where we could filter on Floor, Room and Device type.

    Leave a comment:

Working...
X