Trying to control the RGB led controller (white one) from dx. How do you determine what the address is so you can input it into the plugin output config?
Announcement
Collapse
No announcement yet.
RGB LED's
Collapse
X
-
Originally posted by mk1 black limited View PostI get this in RFXmngr:080301371C04808010...so the code would be...? Sorry...:-)
Packettype = UNDECODED RF Message
UNDECODED ARC:1C04808010
Cheers
AlHS 4.2.8.0: 2134 Devices 1252 Events
Z-Wave 3.0.10.0: 133 Nodes on one Z-Net
Comment
-
Yep, done that. I get this with the Type 2 firmware:
Set Mode:0D 00 00 02 03 53 00 00 02 00 00 00 00 00
------------------------------------------------
0D0100020353AB00020001010000
Packettype = Interface Message
subtype = Interface Response
Sequence nbr = 2
response on cmnd = Set Mode
Transceiver type = 433.92MHz
Firmware version = 171
Hardware version = 1.1
Undec off
X10 disabled
ARC disabled
AC disabled
HomeEasy EU disabled
Meiantech disabled
Oregon Scientific disabled
ATI disabled
Visonic disabled
Mertik disabled
AD enabled
Hideki disabled
La Crosse disabled
FS20 disabled
ProGuard disabled
BlindsT0 disabled
BlindsT1 disabled
AE disabled
RUBiCSON disabled
FineOffset disabled
RFU protocol 3 disabled
RFU protocol 4 disabled
RFU protocol 5 disabled
RFU protocol 6 disabled
------------------------------------------------
0A140602FCCFE300010061
Packettype = Lighting5
ERROR: Unknown Sub type for Packet type=14: 6
Signal level = 6
------------------------------------------------
0A140603FCCFE300010061
Packettype = Lighting5
ERROR: Unknown Sub type for Packet type=14: 6
Signal level = 6
------------------------------------------------
0A140604FCCFE300010061
Packettype = Lighting5
ERROR: Unknown Sub type for Packet type=14: 6
Signal level = 6
Comment
-
I'm at a loss. Your settings look just like mine. Which RGB controller do you have?
This is what I get for each packet:
PHP Code:------------------------------------------------
0A140600FCC51000010061
Packettype = Lighting5
subtype = RGB TRC02
Sequence nbr = 0
ID = FCC510
Command = On
Signal level = 6
Cheers
AlHS 4.2.8.0: 2134 Devices 1252 Events
Z-Wave 3.0.10.0: 133 Nodes on one Z-Net
Comment
-
Add a dx.com RGB LED strip driver
- Flash the RFXtrx433 with Type2 firmware to be able to receive the remote ID in RFXmngr.
- In RFXmngr enable only the AD protocol and press a button on the remote.
- If necessary flash the RFXtrx433 back to Type1 if Type2 does not support devices you need. (See chapter 2.2 in the RFXtrx User Guide.pdf)
- Go to the PLUG-INS - RFXCOM - Output Devices configuration page
- Add the RGB LED output device with the ID found in RFXmngr
Comment
-
Hi Bert, something broke my color device for my dx.com LED controller after the upgrade to .38. The control device seems to be fine, but the color device now has an RFXCom tab that is not filled out. Looking at the manual it indicates that color device should not have an RFXCom tab. Thoughts on how to resolve?
Thanks
Al
EDIT: I recreated the output devices and deleted the old devices and all is well. Not sure how it got messed up in the upgrade, so you may want to check the code associated with that.
HS 4.2.8.0: 2134 Devices 1252 Events
Z-Wave 3.0.10.0: 133 Nodes on one Z-Net
Comment
Comment