Announcement

Collapse
No announcement yet.

Error message filling the log

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Error message filling the log

    Every few days my log gets filled with these error messages. I can restart the plug-in and they stop for a few days, then come back. There is nothing in the HS log that to indicate a cause when the errors start and the HS devices continue to reflect energy consumption.

    What can I do to troubleshoot?

    Sep-28 1:49:22 PMInformationalBrultech ECM Device connection established to COM:11.Sep-28 1:49:22 PMPlug-InFinished initializing plug-in UltraECM3Sep-28 1:49:19 PMInfoPlugin UltraECM3 has connected. IP:127.0.0.1:63816Sep-28 1:49:12 PMInfoPlugin UltraECM3 with instance: has disconnectedSep-28 1:49:12 PMPlug-InShutting down Plug-In: UltraECM3Sep-28 1:48:53 PM1ErrorSystem.OverflowException: Arithmetic operation resulted in an overflow. at HSPI_ULTRAECM3.Channel.processWattSeconds(UInt64 wattseconds, Int64 seconds)Sep-28 1:48:53 PM1ErrorSystem.OverflowExceptionSep-28 1:48:23 PM1ErrorSystem.OverflowException: Arithmetic operation resulted in an overflow. at HSPI_ULTRAECM3.Channel.processWattSeconds(UInt64 wattseconds, Int64 seconds)Sep-28 1:48:23 PM1ErrorSystem.OverflowExceptionSep-28 1:48:22 PM1ErrorSystem.OverflowException: Arithmetic operation resulted in an overflow. at HSPI_ULTRAECM3.Channel.processWattSeconds(UInt64 wattseconds, Int64 seconds)Sep-28 1:48:22 PM1ErrorSystem.OverflowException
    Mike____________________________________________________________ __________________
    HS3 Pro Edition 3.0.0.548, NUC i3

    HW: Stargate | NX8e | CAV6.6 | Squeezebox | PCS | WGL 800RF | RFXCOM | Vantage Pro | Green-Eye | Edgeport/8 | Way2Call | Ecobee3 | EtherRain | Ubiquiti

    #2
    What Brultech device and firmware are you running? What type of com port are you using?

    Regards,
    Ultrajones
    Plug-ins: UltraMon, UltraM1G, UltraCID, Ultra1Wire, UltraLog, UltraWeatherBug, UltraPioneerAVR, UltraGCIR

    Comment


      #3
      It's an ECM-1240, about 4 years old. I'm not sure how to check the firmware, but it hasn't been updated since I installed it.
      The link is serial to usb converter.
      Mike____________________________________________________________ __________________
      HS3 Pro Edition 3.0.0.548, NUC i3

      HW: Stargate | NX8e | CAV6.6 | Squeezebox | PCS | WGL 800RF | RFXCOM | Vantage Pro | Green-Eye | Edgeport/8 | Way2Call | Ecobee3 | EtherRain | Ubiquiti

      Comment


        #4
        When this happens again, please enable debug for about 30 seconds before you restart the plug-in. Send the debug file to ultrajones@hotmail.com before you fire the plug-in back up because you'll overwrite it.

        Regards,
        Ultrajones
        Plug-ins: UltraMon, UltraM1G, UltraCID, Ultra1Wire, UltraLog, UltraWeatherBug, UltraPioneerAVR, UltraGCIR

        Comment


          #5
          I thought it might have magically fixed itself, but the errors returned. Debug log attached.
          Attached Files
          Mike____________________________________________________________ __________________
          HS3 Pro Edition 3.0.0.548, NUC i3

          HW: Stargate | NX8e | CAV6.6 | Squeezebox | PCS | WGL 800RF | RFXCOM | Vantage Pro | Green-Eye | Edgeport/8 | Way2Call | Ecobee3 | EtherRain | Ubiquiti

          Comment


            #6
            Channel 6 Watts is reporting: CH6 Watts=NaN. I'll have to dig into this a bit further.
            Plug-ins: UltraMon, UltraM1G, UltraCID, Ultra1Wire, UltraLog, UltraWeatherBug, UltraPioneerAVR, UltraGCIR

            Comment


              #7
              The issue appears to be isolated to your ECM 1240 channel 6. How do you have that channel configured?
              Plug-ins: UltraMon, UltraM1G, UltraCID, Ultra1Wire, UltraLog, UltraWeatherBug, UltraPioneerAVR, UltraGCIR

              Comment


                #8
                Channel 6 is set up to monitor HVAC with small CTs: furnace, boiler, A/C. I think there may also be a circuit that has a dehumidifier on it, but I'd need to check more carefully to be sure. It's been several years since I paid any attention.

                AFAIK, it's not set up any differently than 3, 4, 5, and 7.
                Mike____________________________________________________________ __________________
                HS3 Pro Edition 3.0.0.548, NUC i3

                HW: Stargate | NX8e | CAV6.6 | Squeezebox | PCS | WGL 800RF | RFXCOM | Vantage Pro | Green-Eye | Edgeport/8 | Way2Call | Ecobee3 | EtherRain | Ubiquiti

                Comment

                Working...
                X