Announcement

Collapse
No announcement yet.

Radio Thermostat v1.0.0.0

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    A new version is now in the forums @
    http://board.homeseer.com/showthread.php?p=1177564

    This version adds a configuration menu where you can manually add the thermostats. I will send to HomeSeer to add to the updater, but it typically takes them few days.

    Comment


      #17
      New version is now in the updater, it adds a config page to manually add thermostats.

      Comment


        #18
        Progress- I can specify the IP...

        Progress- I can specify the IP...
        Error adding thermostat with IP: 192.168.100.239

        Going to the IP (I set it manually on my Themostat.. Everything is fine
        At first I was having json errors but after rebooting the plugin initialized normally.
        I have 13 days left on my trial.

        Comment


          #19
          Originally posted by douggle View Post
          Progress- I can specify the IP...
          Error adding thermostat with IP: 192.168.100.239

          Going to the IP (I set it manually on my Themostat.. Everything is fine
          At first I was having json errors but after rebooting the plugin initialized normally.
          I have 13 days left on my trial.
          So it's working now? Do you have the errors you were getting?

          Comment


            #20
            It is still not working. Below is the only error

            Error adding thermostat with IP: 192.168.100.239

            Comment


              #21
              Originally posted by kingfetty View Post
              This supports the CT-80 as long as it's using the Wifi U-SNAP module and not the Z-Wave. It currently doesn't have the Humidity and Data Areas as functionalities, but I do plan on adding it in a future release.
              Any news on the humidity? Thanks

              Code:
              Nov-29 11:21:46   Plug-In    Interface RadioThermostat is running as a trial, 15 days remaining.   
              Nov-29 11:21:39   Plug-In    Found plug-in: RadioThermostat, version: 1.0.15128.9

              Comment


                #22
                Originally posted by douggle View Post
                Error adding thermostat with IP: 192.168.100.239
                New installation and I have the same issue:

                "Error adding thermostat with IP: 192.168.0.60"

                I am using Version 1.0.15128.9 of plugin and HS3 Pro Edition 3.0.0.208 with Windows 10.

                Elliott
                "Living with technology means living in a [constant] state of flux." S. Higgenbotham, 2023
                "Reboot and rejoice!" F. Pishotta, 1989

                Comment


                  #23
                  Originally posted by Richel View Post
                  New installation and I have the same issue:

                  "Error adding thermostat with IP: 192.168.0.60"

                  I am using Version 1.0.15128.9 of plugin and HS3 Pro Edition 3.0.0.208 with Windows 10.

                  Elliott
                  You need to create a config file as detailed in this thread: http://board.homeseer.com/showthread.php?t=174508

                  Comment


                    #24
                    Originally posted by joey52685 View Post
                    You need to create a config file as detailed in this thread: http://board.homeseer.com/showthread.php?t=174508
                    Thanks. That worked.

                    Elliott
                    "Living with technology means living in a [constant] state of flux." S. Higgenbotham, 2023
                    "Reboot and rejoice!" F. Pishotta, 1989

                    Comment


                      #25

                      Comment


                        #26
                        I'm unable to find a published API document for either of those.

                        Comment


                          #27
                          Originally posted by spknapp View Post
                          Is the CT-80 supported and its extra features (humidity get/set, data areas)?

                          Thanks,
                          Steve
                          Originally posted by kingfetty View Post
                          This supports the CT-80 as long as it's using the Wifi U-SNAP module and not the Z-Wave. It currently doesn't have the Humidity and Data Areas as functionalities, but I do plan on adding it in a future release.
                          Originally posted by dovla View Post
                          Any news on the humidity? Thanks

                          Code:
                          Nov-29 11:21:46   Plug-In    Interface RadioThermostat is running as a trial, 15 days remaining.   
                          Nov-29 11:21:39   Plug-In    Found plug-in: RadioThermostat, version: 1.0.15128.9
                          Eric - any progress made on supporting the additional features of the CT-80 (humidity and user areas) or do you have any time frame in mind for these features?

                          Thanks
                          Steve

                          (System configuration is in my profile)

                          Comment


                            #28
                            Originally posted by spknapp View Post
                            Eric - any progress made on supporting the additional features of the CT-80 (humidity and user areas) or do you have any time frame in mind for these features?

                            Thanks
                            It's still in my task list, but lately I've been battling some bugs with the plugin and some very odd circumstances. Once I reach stability on that front I will begin adding new features.

                            Comment


                              #29
                              Originally posted by spknapp View Post
                              Is the CT-80 supported and its extra features (humidity get/set, data areas)?

                              Thanks,
                              Steve
                              Originally posted by kingfetty View Post
                              This supports the CT-80 as long as it's using the Wifi U-SNAP module and not the Z-Wave. It currently doesn't have the Humidity and Data Areas as functionalities, but I do plan on adding it in a future release.
                              Originally posted by dovla View Post
                              Any news on the humidity? Thanks
                              Eric - what is the status of implementing the features that are missing from your plugin? I am referring to the basic features that you left out as well as the additional features of the CT-80 thermostat? It's been over a year since you addressed this question.

                              Basic features missing for all thermostats:
                              - Disable thermostat internal schedule
                              - Disable cloud reporting feature
                              - Price Messaging Area (PMA)

                              CT-80 features missing:
                              - Humidity control
                              - User Messaging Area (UMA)
                              - Control of night light (display backlight)

                              The plugin has been out for a while and yet these features are still missing.

                              Thanks,
                              Steve
                              Steve

                              (System configuration is in my profile)

                              Comment


                                #30
                                Originally posted by spknapp View Post
                                Eric - what is the status of implementing the features that are missing from your plugin? I am referring to the basic features that you left out as well as the additional features of the CT-80 thermostat? It's been over a year since you addressed this question.

                                Basic features missing for all thermostats:
                                - Disable thermostat internal schedule
                                - Disable cloud reporting feature
                                - Price Messaging Area (PMA)

                                CT-80 features missing:
                                - Humidity control
                                - User Messaging Area (UMA)
                                - Control of night light (display backlight)

                                The plugin has been out for a while and yet these features are still missing.

                                Thanks,
                                Steve

                                Honestly, I totally forgot, sorry. I appreciate the nudge. Let me see what I can do for you over the next couple weeks.

                                Comment

                                Working...
                                X