View Single Post
  #102  
Old September 24th, 2016, 08:01 AM
Ultrajones's Avatar
Ultrajones Ultrajones is offline
OverSeer
 
Join Date: Jan 2001
Location: Michigan, US
Posts: 5,771
Quote:
Originally Posted by Pete View Post
Hello Randy,

Telnet doesn't work here for me with the Pioneer VSX-44

pete@ICS-HPLT:~$ telnet 192.168.244.254
Trying 192.168.244.254...
telnet: Unable to connect to remote host: Connection refused


Trying a port scan to see what is open.

]nmap 192.168.244.254 -p1-500

Starting Nmap 7.01 (hxxps://nmap.org) at 2016-09-24 05:43 CDT
Nmap scan report for 192.168.244.254
Host is up (0.030s latency).
Not shown: 498 closed ports
PORT STATE SERVICE
80/tcp open http
443/tcp open https
MAC Address: (Pioneer)

501-1000

Shows nothing

nmap 192.168.244.254 -p1001-3000

Starting Nmap 7.01 (hxxps://nmap.org) at 2016-09-24 05:50 CDT
Nmap scan report for 192.168.244.254
Host is up (0.0020s latency).
Not shown: 1998 closed ports
PORT STATE SERVICE
1026/tcp open LSA-or-nterm
1900/tcp open upnp

Telnet works with port 1026 so will try that one.

OK so configured IP as
192.168.244.254:1026

And now it connects fine. Thank you Randy.

Going baby steps here cuz I have never used Homeseer with IR blasting or remote control of AVR devices (just the Russound here).

Tried the power off control and noticed that it doesn't work. What command window?

Sep-24 6:10:13 AM Informational Watchdog Timer reconnect attempt succeeded.
Sep-24 6:10:16 AM Warning No response/improper response from Pioneer AVR device '192.168.244.254:1026' to command 'PO'. Your Pioneer AVR may not support the feature 'Power'.
Sep-24 6:10:20 AM Warning No response/improper response from Pioneer AVR device '192.168.244.254:1026' to command '?P'. Your Pioneer AVR may not support the feature 'Power'.
Sep-24 6:10:25 AM Warning No response/improper response from Pioneer AVR device '192.168.244.254:1026' to command '?P'. Your Pioneer AVR may not support the feature 'Power'.



When I manually telnet to port 1026 and enter twice it closes the telnet window.

Changed port to 8102 and it responds now to Pioneer commands.

telnet 192.168.244.254 8102
Trying 192.168.244.254...
Connected to 192.168.244.254.
Escape character is '^]'.
P?
R
R

OK power off works but disconnects the AVR from the network. IE: no ping response when AVR is off.

Is there a standby command?

Quick question.

Wife cannot deal with Pioneer remote (too small of buttons?) and Logitech remote screen (print is too small).

Do you have any suggestions for a large button Pioneer VSX remote control?

I do not know if an HSTouch screen on a tablet will work for her.

Found this old command line document and attached it as I was trying these commands.
Pete, please enter the receiver menu from your remote to view the network settings. You need to verify network standby is turned on. Also check to see if your receiver allows you to enable other ports other than the Pioneer App port of 8102. Please Note: The ports on the Pioneer only allow 1 simultaneous connection, so if you're connected via telnet, you won't be able to connect via the plugin.

I am not aware of any big button Pioneer remote control. I assume any programmable remote with big buttons will work. You only need a small subset of the Pioneer buttons for it to be a functional remote.

Regards,
Ultrajones
__________________
Plug-ins: UltraMon, UltraM1G, UltraCID, Ultra1Wire, UltraLog, UltraWeatherBug, UltraPioneerAVR, UltraGCIR
Reply With Quote