Will not update a device that is included.
Is HS remembering last state (that I set) or is the priority a powerfail recovery settings?
--- PIM IFORMATION ---
9/20/2011 03:46:36 PM UPB Network ID: FF
9/20/2011 03:46:36 PM UPB Module ID: 30
9/20/2011 03:46:36 PM UPB UPB Options: 00000000
9/20/2011 03:46:36 PM UPB UPB Version: 1
9/20/2011 03:46:36 PM UPB Manufacturer ID: 04
9/20/2011 03:46:36 PM UPB Product ID: 030
9/20/2011 03:46:36 PM UPB Firmware Version: 4.17
9/20/2011 03:46:36 PM UPB PIM Options: 11110011
9/20/2011 03:46:36 PM UPB (Message Mode Enabled)
9/20/2011 03:46:36 PM UPB ----------------------
Does anyone have a stable working Include in Power Fail Recovery
function working. I have a number of devices set for this but after a HS stop and restart, the device is not changed to the last 12 hours that I have configured.
IF I have an event where a device will turn on at 3:20 PM and have it - Include in Power Fail Recovery - checked. at 3:30 PM , I turn that device off and I stop HS and then start HS.
The powerfail should update the device if it is within the range of configuration.
Enable event catch-up upon power restoration: Yes
Number of hours to catch-up: 12
Allow scripts to run during recovery?: Yes
At startup, delay recovery by 120 seconds
Tested it again, not working. I do not see a log of this recovery running either? IS this normal?
Entries are:
9/20/2011 03:33:34 PM System Synchronizing events from 9/20/2011 03:33:00 AM until now
9/20/2011 03:33:34 PM System Synchronizing Events: Waiting for event actions to process...
9/20/2011 03:33:34 PM System Synchronization complete, updating devices
but the 3:20 PM event is not run.
Anyone having this same issue on the UBP plugin?
Is HS remembering last state (that I set) or is the priority a powerfail recovery settings?
--- PIM IFORMATION ---
9/20/2011 03:46:36 PM UPB Network ID: FF
9/20/2011 03:46:36 PM UPB Module ID: 30
9/20/2011 03:46:36 PM UPB UPB Options: 00000000
9/20/2011 03:46:36 PM UPB UPB Version: 1
9/20/2011 03:46:36 PM UPB Manufacturer ID: 04
9/20/2011 03:46:36 PM UPB Product ID: 030
9/20/2011 03:46:36 PM UPB Firmware Version: 4.17
9/20/2011 03:46:36 PM UPB PIM Options: 11110011
9/20/2011 03:46:36 PM UPB (Message Mode Enabled)
9/20/2011 03:46:36 PM UPB ----------------------
Does anyone have a stable working Include in Power Fail Recovery
function working. I have a number of devices set for this but after a HS stop and restart, the device is not changed to the last 12 hours that I have configured.
IF I have an event where a device will turn on at 3:20 PM and have it - Include in Power Fail Recovery - checked. at 3:30 PM , I turn that device off and I stop HS and then start HS.
The powerfail should update the device if it is within the range of configuration.
Enable event catch-up upon power restoration: Yes
Number of hours to catch-up: 12
Allow scripts to run during recovery?: Yes
At startup, delay recovery by 120 seconds
Tested it again, not working. I do not see a log of this recovery running either? IS this normal?
Entries are:
9/20/2011 03:33:34 PM System Synchronizing events from 9/20/2011 03:33:00 AM until now
9/20/2011 03:33:34 PM System Synchronizing Events: Waiting for event actions to process...
9/20/2011 03:33:34 PM System Synchronization complete, updating devices
but the 3:20 PM event is not run.
Anyone having this same issue on the UBP plugin?
Comment