I received my LS100 Leak Sensor today and went to install it using my iPad Z-Tool+ app and SmartStick+ controller. When I added (unsecured) it only added two devices (as Node 3):
Neither of which resemble the root device, and do not look like the device shown in this post. So, I removed it, and added it again as unsecured (Node 4), and still it only added the same two devices. Is this right? If so, which is the root? If not, what am I doing wrong?
Thanks
Gary
Mar-09 2:07:29 PM Z-Wave Device: Node 4 Z-Wave Battery Set to 88
Mar-09 2:07:23 PM Z-Wave 5 out of 5 Child devices of node 4 were created successfully.
Mar-09 2:07:23 PM Z-Wave Setting wake-up interval for device Node 4 Z-Wave HomeSeer Leak Sensor to 12 hours and 0 minutes.
Mar-09 2:07:23 PM Z-Wave Programming device Node 4 Z-Wave HomeSeer Leak Sensor (4) to send wake-up notifications to HomeSeer.
Mar-09 2:07:22 PM Z-Wave Getting association information for Node 4 Z-Wave HomeSeer Leak Sensor
Mar-09 2:07:22 PM Z-Wave Assigning return route from node 1 to Node 4 Z-Wave HomeSeer Leak Sensor
Mar-09 2:07:21 PM Z-Wave SmartStick+: Adding association for Z-Wave device Node 4 Z-Wave HomeSeer Leak Sensor (Node 4, Group 1) to HomeSeer
Mar-09 2:07:21 PM Z-Wave Root Node Device Node 4 Z-Wave HomeSeer Leak Sensor was created for node 4 on network FC10065A
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Z-Wave All associations for node 4 have been retrieved successfully, it supports associations on these groups: 1, 2.
Mar-09 2:07:21 PM Z-Wave Node 4 Association Group 2 can have 5 associations, and currently has 0
Mar-09 2:07:21 PM Z-Wave Node 4 Association Group 1 can have 5 associations, and currently has 0
Mar-09 2:07:21 PM Z-Wave Getting association information for node 4
Mar-09 2:07:21 PM Z-Wave Node 4 is a V2 Binary Sensor. Supported Sensors: Heat, Water, Freeze, Tamper
Mar-09 2:07:20 PM Z-Wave Node 4 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully.
Mar-09 2:07:19 PM Z-Wave Node 4 is a Z-Wave Plus node. Retrieving ZWPlus Info...
Mar-09 2:07:19 PM Z-Wave Node 4 is Z-Wave version: Lib: 4.61 App: 1.2
Mar-09 2:07:19 PM Z-Wave Node: 4 Supports Class(es): ZWAVEPLUS_INFO, ASSOCIATION_V2, ASSOCIATION_GRP_INFO_V2, TRANSPORT_SERVICE, VERSION_V2, MANUFACTURER_SPECIFIC_V2, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, NOTIFICATION_V6, WAKE_UP, CONFIGURATION_V4, SUPERVISION, SENSOR_MULTILEVEL_V7, SENSOR_BINARY, FIRMWARE_UPDATE_MD_V2
Mar-09 2:07:19 PM Z-Wave Z-Wave manufacturer information for node 4, ID: 12=CH (HomeSeer Tech), Type: 513=201H, ID: 10=AH
Mar-09 2:07:19 PM Z-Wave Synchronize nodes finished. Number of device nodes to be created/added = 1
Mar-09 2:07:16 PM Z-Wave Done. Node 4 Added.
Current Date/Time: 3/9/2018 2:35:11 PM
HomeSeer Version: HS3 Pro Edition 3.0.0.409
Operating System: Microsoft Windows 8.1 Pro with Media Center - Work Station
System Uptime: 5 Days 2 Hours 20 Minutes 56 Seconds
IP Address: 192.168.1.83
Number of Devices: 249
Number of Events: 61
Available Threads: 800
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed: Windows Defender Malwarebytes
Enabled Plug-Ins
2.0.54.0: BLOnkyo
2.18.0.3: MCSSPRINKLERSP
30.0.0.36: RFXCOM
3.0.6551.16959: UltraGCIR3
3.0.0.40: X10
3.0.1.190: Z-Wave
Neither of which resemble the root device, and do not look like the device shown in this post. So, I removed it, and added it again as unsecured (Node 4), and still it only added the same two devices. Is this right? If so, which is the root? If not, what am I doing wrong?
Thanks
Gary
Mar-09 2:07:29 PM Z-Wave Device: Node 4 Z-Wave Battery Set to 88
Mar-09 2:07:23 PM Z-Wave 5 out of 5 Child devices of node 4 were created successfully.
Mar-09 2:07:23 PM Z-Wave Setting wake-up interval for device Node 4 Z-Wave HomeSeer Leak Sensor to 12 hours and 0 minutes.
Mar-09 2:07:23 PM Z-Wave Programming device Node 4 Z-Wave HomeSeer Leak Sensor (4) to send wake-up notifications to HomeSeer.
Mar-09 2:07:22 PM Z-Wave Getting association information for Node 4 Z-Wave HomeSeer Leak Sensor
Mar-09 2:07:22 PM Z-Wave Assigning return route from node 1 to Node 4 Z-Wave HomeSeer Leak Sensor
Mar-09 2:07:21 PM Z-Wave SmartStick+: Adding association for Z-Wave device Node 4 Z-Wave HomeSeer Leak Sensor (Node 4, Group 1) to HomeSeer
Mar-09 2:07:21 PM Z-Wave Root Node Device Node 4 Z-Wave HomeSeer Leak Sensor was created for node 4 on network FC10065A
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Error BuildDeviceVoiceCommands error (1), Object reference not set to an instance of an object., Scheduler
Mar-09 2:07:21 PM Z-Wave All associations for node 4 have been retrieved successfully, it supports associations on these groups: 1, 2.
Mar-09 2:07:21 PM Z-Wave Node 4 Association Group 2 can have 5 associations, and currently has 0
Mar-09 2:07:21 PM Z-Wave Node 4 Association Group 1 can have 5 associations, and currently has 0
Mar-09 2:07:21 PM Z-Wave Getting association information for node 4
Mar-09 2:07:21 PM Z-Wave Node 4 is a V2 Binary Sensor. Supported Sensors: Heat, Water, Freeze, Tamper
Mar-09 2:07:20 PM Z-Wave Node 4 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully.
Mar-09 2:07:19 PM Z-Wave Node 4 is a Z-Wave Plus node. Retrieving ZWPlus Info...
Mar-09 2:07:19 PM Z-Wave Node 4 is Z-Wave version: Lib: 4.61 App: 1.2
Mar-09 2:07:19 PM Z-Wave Node: 4 Supports Class(es): ZWAVEPLUS_INFO, ASSOCIATION_V2, ASSOCIATION_GRP_INFO_V2, TRANSPORT_SERVICE, VERSION_V2, MANUFACTURER_SPECIFIC_V2, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, NOTIFICATION_V6, WAKE_UP, CONFIGURATION_V4, SUPERVISION, SENSOR_MULTILEVEL_V7, SENSOR_BINARY, FIRMWARE_UPDATE_MD_V2
Mar-09 2:07:19 PM Z-Wave Z-Wave manufacturer information for node 4, ID: 12=CH (HomeSeer Tech), Type: 513=201H, ID: 10=AH
Mar-09 2:07:19 PM Z-Wave Synchronize nodes finished. Number of device nodes to be created/added = 1
Mar-09 2:07:16 PM Z-Wave Done. Node 4 Added.
Current Date/Time: 3/9/2018 2:35:11 PM
HomeSeer Version: HS3 Pro Edition 3.0.0.409
Operating System: Microsoft Windows 8.1 Pro with Media Center - Work Station
System Uptime: 5 Days 2 Hours 20 Minutes 56 Seconds
IP Address: 192.168.1.83
Number of Devices: 249
Number of Events: 61
Available Threads: 800
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed: Windows Defender Malwarebytes
Enabled Plug-Ins
2.0.54.0: BLOnkyo
2.18.0.3: MCSSPRINKLERSP
30.0.0.36: RFXCOM
3.0.6551.16959: UltraGCIR3
3.0.0.40: X10
3.0.1.190: Z-Wave
Comment