I picked up one of these from Monoprice. Nice to have power control and usb charging in one.
It got included successfully and it does get recognized with the correct picture in HS. Nice! I opened the little configuration guide and I found that it has quite a few device settings. Unfortunately, they aren't listed in the HS ZWave configuration page for the device. It only has one setting. . .how to respond to the all on / all off command.
I assume these have to be added into the definition of the ZWave devices somehow to show up in the device config? I am documenting the setting here in case they can be added.
The Configuration options it offers:
Overload Protection:
Parameter #: 20
Default: 1
Parameter Size: 1byte
0 - Overload protection disabled
1 - Overload protection enabled
Status Memory:
Parameter #:21
Default: 0
Parameter Size: 1byte
0 - Remembers previous state at power loss
1 - Always On when restored
2 - Always Off when restored
Load Status Change Notification:
Parameter #:24
Default: 1
Parameter Size: 1byte
0 - Notifications disabled
1 - BASIC REPORT sent when power load changes
2 - BASIC REPORT sent when power load changes with non Z-Wave command
LED Indicator Modes
Parameter #:27
Default: 1
Parameter Size: 1byte
0 - LED on when powered on, off when powered off
1 - LED on when powered on, turns off after 5 seconds without Z-Wave command or button press
Absolute Threshold of Power Report:
Parameter #:151
Default: 50 (watts)
Parameter Size: 2bytes
0 - Power report disabled
1 - 65535 - Number of watts by which the load must change to trigger a power report
Percentage Threshold of Power Report:
Parameter #:152
Default: 10 (%)
Parameter Size: 1byte
0 - Power report disabled
1 - 255 - Percentage the power load must change to trigger power report
Power Report Interval:
Parameter #:171
Default: 30 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows power report to be send when power load changes
5 - 2678400 - Number of seconds before another power report is sent
Energy Report Interval:
Parameter #:172
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows energy report to be send when power load changes
5 - 2678400 - Number of seconds before another energy report is sent
Voltage Report Interval:
Parameter #:173
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows voltage report to be send when power load changes
5 - 2678400 - Number of seconds before another voltage report is sent
Electricity Report Interval:
Parameter #:174
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows electricity level report to be send when power load changes
5 - 2678400 - Number of seconds before another electricity level report is sent
It got included successfully and it does get recognized with the correct picture in HS. Nice! I opened the little configuration guide and I found that it has quite a few device settings. Unfortunately, they aren't listed in the HS ZWave configuration page for the device. It only has one setting. . .how to respond to the all on / all off command.
I assume these have to be added into the definition of the ZWave devices somehow to show up in the device config? I am documenting the setting here in case they can be added.
The Configuration options it offers:
Overload Protection:
Parameter #: 20
Default: 1
Parameter Size: 1byte
0 - Overload protection disabled
1 - Overload protection enabled
Status Memory:
Parameter #:21
Default: 0
Parameter Size: 1byte
0 - Remembers previous state at power loss
1 - Always On when restored
2 - Always Off when restored
Load Status Change Notification:
Parameter #:24
Default: 1
Parameter Size: 1byte
0 - Notifications disabled
1 - BASIC REPORT sent when power load changes
2 - BASIC REPORT sent when power load changes with non Z-Wave command
LED Indicator Modes
Parameter #:27
Default: 1
Parameter Size: 1byte
0 - LED on when powered on, off when powered off
1 - LED on when powered on, turns off after 5 seconds without Z-Wave command or button press
Absolute Threshold of Power Report:
Parameter #:151
Default: 50 (watts)
Parameter Size: 2bytes
0 - Power report disabled
1 - 65535 - Number of watts by which the load must change to trigger a power report
Percentage Threshold of Power Report:
Parameter #:152
Default: 10 (%)
Parameter Size: 1byte
0 - Power report disabled
1 - 255 - Percentage the power load must change to trigger power report
Power Report Interval:
Parameter #:171
Default: 30 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows power report to be send when power load changes
5 - 2678400 - Number of seconds before another power report is sent
Energy Report Interval:
Parameter #:172
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows energy report to be send when power load changes
5 - 2678400 - Number of seconds before another energy report is sent
Voltage Report Interval:
Parameter #:173
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows voltage report to be send when power load changes
5 - 2678400 - Number of seconds before another voltage report is sent
Electricity Report Interval:
Parameter #:174
Default: 300 (seconds)
Parameter Size: 4bytes
0 - Interval disabled - allows electricity level report to be send when power load changes
5 - 2678400 - Number of seconds before another electricity level report is sent
Comment