www.homeseer.com    
 

Go Back   HomeSeer Message Board > User Interface Plug-ins > User Interface Discussion > ImperiHome Plug-in (3P)

Reply
 
Thread Tools Display Modes
  #61  
Old Yesterday, 12:23 PM
rjh's Avatar
rjh rjh is offline
HomeSeer Technologies
 
Join Date: Jan 2001
Location: Bedford, NH, USA
Posts: 8,280
We made some event changes, can you try build 398 and see if there is any change:

https://homeseer.com/updates3/SetupHS3_3_0_0_398.msi

Quote:
Originally Posted by peterpc View Post
When lights go on very slow, I noticed the following:
I have an event that will trigger on motion and a virtual device to show the status of the lights.
It runs when light status is off and switches on the light and set the virtual device to on.
In the log I see this:
Dec-16 16:36:45 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:40 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:35 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:30 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:25 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:20 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:15 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:15 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:14 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)
Dec-16 16:36:14 Device Control Device: Eerste_verdieping: Hobbykamer Licht status to On (100)

Multiple device controls to set the status on, but the event should only trigger once to set the status on.

I have attached the event.

When I trigger the event again by switching of the status device, the status device triggers only once.

I think that will explain that sometimes the lights go on within one second and sometimes it takes 10 to 15 seconds.

I even have noticed that a light goes on, off again and on again because the event to switch off the light was triggered right after the event to turn on the lights.
Hope this helps to find the delay problem.
__________________
Rich,


website | products | support | youtube
Reply With Quote
  #62  
Old Yesterday, 01:42 PM
peterpc's Avatar
peterpc peterpc is offline
Seer Master
 
Join Date: May 2003
Location: the Netherlands
Posts: 643
Still a problem:
Dec-16 18:32:33 NO ECHO No Echo for Slaapkamer Slaapkamer, Echo (3 secs)
Dec-16 18:32:31 ECHO Echo for Slaapkamer Slaapkamer, No Echo (1 secs)
Dec-16 18:32:29 NO ECHO No Echo for Slaapkamer Slaapkamer, Echo (3 secs)
Dec-16 18:32:27 ECHO Echo for Slaapkamer Slaapkamer, No Echo (8 secs)
Dec-16 18:32:27 Device Control Device: Eerste_verdieping: Slaapkamer Licht status to On (100)
Dec-16 18:32:27 Device Control Device: Insteon Slaapkamer spiegel(I) to Dim 99% (99)
Dec-16 18:32:27 Event Event Trigger "Slaapkamer beweging licht aan en tv is uit"
Dec-16 18:32:17 NO ECHO No Echo for Slaapkamer Slaapkamer, Echo (3 secs)
Dec-16 18:32:15 Device Control Device: Eerste_verdieping: Slaapkamer Licht status to On (100)
Dec-16 18:32:15 Device Control Device: Insteon Slaapkamer spiegel(I) to Dim 99% (99)
Dec-16 18:32:15 Event Event Trigger "Slaapkamer beweging licht aan en tv is uit"
Dec-16 18:32:15 ECHO Echo for Slaapkamer Slaapkamer, No Echo (14 secs)
Dec-16 18:32:00 NO ECHO No Echo for Slaapkamer Slaapkamer, Echo (3 secs)
Dec-16 18:31:58 ECHO Echo for Slaapkamer Slaapkamer, No Echo (5 secs)
Dec-16 18:31:58 Device Control Device: Eerste_verdieping: Slaapkamer Licht status to On (100)
Dec-16 18:31:58 Device Control Device: Insteon Slaapkamer spiegel(I) to Dim 99% (99)
Dec-16 18:31:58 Event Event Trigger "Slaapkamer beweging licht aan en tv is uit"
Dec-16 18:31:52 NO ECHO No Echo for Slaapkamer Slaapkamer, Echo (1 secs)
Dec-16 18:31:52 ACTIVE ZONE Slaapkamer Slaapkamer bezet has changed to Active Zone On, Active Zone Off (2 mins, 3 secs)
Dec-16 18:31:51 ECHO Echo for Slaapkamer Slaapkamer, No Echo (4 mins, 3 secs)
Dec-16 18:31:51 Device Control Device: Eerste_verdieping: Slaapkamer Licht status to On (100)
Dec-16 18:31:51 Device Control Device: Insteon Slaapkamer spiegel(I) to Dim 99% (99)
Dec-16 18:31:51 Event Event Trigger "Slaapkamer beweging licht aan en tv is uit"
Attached Images
 
__________________
Peter

http://ohh.pcgsm.nl
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Status Not Updating cyancey BLFloorplan (3P) 0 August 31st, 2016 06:38 PM
Status not updating? surovich Nest Devices (3P) 13 April 26th, 2015 06:03 PM
Status page not updating lamp status Stevieboy HomeSeer Z-Wave Plug-in 4 September 11th, 2012 11:17 AM
status not updating johnnybwis Insteon Plug-in (Mark Sandler) 8 July 19th, 2010 04:07 PM
Elk M1 status not updating Stef HSTouch™ 12 April 3rd, 2009 05:23 PM


All times are GMT -4. The time now is 06:05 AM.


Copyright HomeSeer Technologies, LLC