Motion Sensor II registering in log but device not updating and events not triggering
Hi Mark
I am running version 3.0.6.33 of the Insteon plug in. The motion sensor II is giving me a problem I have not seen before with other devices.
The occupancy sensor when triggered shows up in the HS3 log. However, the device on the home page is not updated and events are not triggered based on the occupancy sensor changing to Motion or 100.
I have reset the motion sensor and re-programmed for homeseer. I have pasted the .ini entry below:
[Device 61]
DatabaseDelta=25
DeviceID=4A.65.DF
DeviceLocation=Back Courtyard
DeviceName=Entry Fence Motion Sensor 2
DeviceType=1016
EEValues=Mode=32,PIRDelay=3,HeartbeatInterval=16,LowBatteryL evel=133,TempCalibration=5,PowerSource=Battery,OpFlags2=32,L EDBrightness=0
FailedInteractions=23
FirmwareVer=46
HopData=10144,9340,688,116
LastContact=4/27/2018 10:36:30 PM
Link 1=EA 01 41 05 23 00 00 01 1
Link 2=E2 02 41 05 23 00 00 02 2
Link 3=E2 03 41 05 23 00 00 03 3
Link 4=E2 04 41 05 23 00 00 04 4
Link 5=E2 10 41 05 23 00 00 10 5
Link 6=E2 0B 41 05 23 00 00 0B 6
Link 7=E2 01 41 05 23 00 00 01 7
LinksDownloaded=1
NumLinks=7
PollingInterval=0
Protocol=3
RecentDatabaseDelta=25
TotalInteractions=159
Here is an example of a log entry that doesn't register as a device change or a trigger:
May-06 3:22:23 AM Insteon Received Back Courtyard Entry Fence Motion Sensor 2 Occupancy Sensor: (4A.65.DF) Go ON
I do note that the heartbeat/temperature entries do update in the device page.
Lastly, I have found that the Night Only triggers all the time and not just during night time. That could be because my dusk/dawn sensor is not updating. Perhaps I have a bad piece of hardware on top of the issues mentioned above.
Please let me know if you have any suggestions.
Kind regards
Jono
Hi Mark
I am running version 3.0.6.33 of the Insteon plug in. The motion sensor II is giving me a problem I have not seen before with other devices.
The occupancy sensor when triggered shows up in the HS3 log. However, the device on the home page is not updated and events are not triggered based on the occupancy sensor changing to Motion or 100.
I have reset the motion sensor and re-programmed for homeseer. I have pasted the .ini entry below:
[Device 61]
DatabaseDelta=25
DeviceID=4A.65.DF
DeviceLocation=Back Courtyard
DeviceName=Entry Fence Motion Sensor 2
DeviceType=1016
EEValues=Mode=32,PIRDelay=3,HeartbeatInterval=16,LowBatteryL evel=133,TempCalibration=5,PowerSource=Battery,OpFlags2=32,L EDBrightness=0
FailedInteractions=23
FirmwareVer=46
HopData=10144,9340,688,116
LastContact=4/27/2018 10:36:30 PM
Link 1=EA 01 41 05 23 00 00 01 1
Link 2=E2 02 41 05 23 00 00 02 2
Link 3=E2 03 41 05 23 00 00 03 3
Link 4=E2 04 41 05 23 00 00 04 4
Link 5=E2 10 41 05 23 00 00 10 5
Link 6=E2 0B 41 05 23 00 00 0B 6
Link 7=E2 01 41 05 23 00 00 01 7
LinksDownloaded=1
NumLinks=7
PollingInterval=0
Protocol=3
RecentDatabaseDelta=25
TotalInteractions=159
Here is an example of a log entry that doesn't register as a device change or a trigger:
May-06 3:22:23 AM Insteon Received Back Courtyard Entry Fence Motion Sensor 2 Occupancy Sensor: (4A.65.DF) Go ON
I do note that the heartbeat/temperature entries do update in the device page.
Lastly, I have found that the Night Only triggers all the time and not just during night time. That could be because my dusk/dawn sensor is not updating. Perhaps I have a bad piece of hardware on top of the issues mentioned above.
Please let me know if you have any suggestions.
Kind regards
Jono
Comment