Originally posted by timlacey
View Post
Announcement
Collapse
No announcement yet.
ISY Insteon 3.0.0.54 - Beta 54 for HS3
Collapse
This is a sticky topic.
X
X
-
-
One more thing. When my PC restarts, Homeseer runs automatically after a 2 minute delay. This used to be very helpful for remote restarts or for running windows update and then restarting.
The plug-in always fails to start up the first time after Windows PC boot. I always get an error in the start up log and the plug-in is not listed at all in the web interface. I then have to restart Homeseer, after which I have to manually enable the plug-in, which then initializes and works properly.
Tim
Comment
-
Hi Ltek,
Yes, you should see both status and control from manually activated devices. If the load status changes, that should be reported by the ISY to the plug-in and the plug-in's device updated. When the manually activated device sends out a control (I.E. switched on) that also should get reported and is available in the plug-in as a trigger event (when device sends an on command, do something).
For something like a dimmer switch, there should be a two way chain of communication happening:
switch -> ISY -> HS plugin
HS plugin -> ISY -> switch
Knowing what happens at each point when you change the device state at the switch and at the plug-in can help pinpoint where the problem is.
Originally posted by Ltek View Post@bpwwer
Is the plugin supposed to report Status from manually switched devices?
I'm not seeing any status being reported when I turn on/off/dim at the device manually.
thx
Comment
-
Is status correctly changing on the ISY admin console?
The plug-in subscribes to messages from the ISY. There isn't really any control over what it gets from the ISY, it's either all or nothing. With the log level at notices, you should see most of the messages that the ISY sends showing up in the log, if nothing is showing up, it probably means the ISY isn't sending anything.
If the status is changing on the ISY, then it should be sending messages.
If the status isn't changing on the ISY, then it's probably the Insteon links between the ISY/PLM and the device that are wrong.
If the ISY is sending the messages but the HS device isn't responding, then it's probably the link between the HS record and the ISY that's wrong. in this case, deleting the HS record and restarting the plug-in should re-create the HS record with the proper link.
Comment
-
The issue is with the ISY... I don't know what but the ISY is not seeing status updates.
Any way to have the ISY re-do all the device links (hoping that helps)?
Originally posted by bpwwer View PostIs status correctly changing on the ISY admin console?
The plug-in subscribes to messages from the ISY. There isn't really any control over what it gets from the ISY, it's either all or nothing. With the log level at notices, you should see most of the messages that the ISY sends showing up in the log, if nothing is showing up, it probably means the ISY isn't sending anything.
If the status is changing on the ISY, then it should be sending messages.
If the status isn't changing on the ISY, then it's probably the Insteon links between the ISY/PLM and the device that are wrong.
If the ISY is sending the messages but the HS device isn't responding, then it's probably the link between the HS record and the ISY that's wrong. in this case, deleting the HS record and restarting the plug-in should re-create the HS record with the proper link.
Comment
-
See http://wiki.universal-devices.com/in...itle=Main_Page
There is a section on INSTEON no status feedback from devices in the wiki.
Comment
-
Originally posted by bpwwer View PostSee http://wiki.universal-devices.com/in...itle=Main_Page
There is a section on INSTEON no status feedback from devices in the wiki.
I had to call tech support but we figured it out. When I replaced the PLM a few months ago something happened and the links didnt get into the PLM. I had to restore an old config backup and then do "Restore Devices"
Comment
-
Hey Bob. I just tried the update to .50 as it appeared available but have seen some issues, so I've got back to .49.
Event log showed the following - let me know what debug to enable if you want me to try and catch where it's failing.
Dec-09 8:19:08 AM Warning I/O interface ISYInsteon is down, executable is not running, restarting ...
Dec-09 8:19:03 AM Error Calling HSEvent in plugin ISYInsteon, Instance :Object reference not set to an instance of an object.
Dec-09 8:19:03 AM Info Plugin ISYInsteon with instance: has disconnected
Dec-09 8:18:59 AM ISYInsteon Verifying HomeSeer device records, this may take a while.
Dec-09 8:18:45 AM ISYInsteon + 21100 Z-Wave
Dec-09 8:18:45 AM ISYInsteon GetModulesConfig : ISY module configuration Portal Integration - MobiLinc ( 21073) is not currently supported.
Dec-09 8:18:45 AM ISYInsteon + 21073 Portal Integration - MobiLinc
Dec-09 8:18:45 AM ISYInsteon + 21090 Elk Security System
Dec-09 8:18:45 AM ISYInsteon GetModulesConfig : ISY module configuration RCS Zigbee Device Support ( 22000) is not currently supported.
Dec-09 8:18:45 AM ISYInsteon + 22000 RCS Zigbee Device Support
Dec-09 8:18:45 AM ISYInsteon + 21040 Networking Module
Dec-09 8:18:45 AM ISYInsteon + 21011 Electricity Monitor
Dec-09 8:18:45 AM ISYInsteon + 21010 OpenADR
Dec-09 8:18:45 AM ISYInsteon Modules installed on ISY:
Dec-09 8:18:09 AM ISYInsteon ISY Firmware version: 4.6.2
Dec-09 8:18:08 AM Info Plugin ISYInsteon has connected. IP:127.0.0.1:57080
Dec-09 8:18:08 AM ISYInsteon I have connected to HS
Comment
-
Originally posted by grtaylor View PostHey Bob. I just tried the update to .50 as it appeared available but have seen some issues, so I've got back to .49.
Event log showed the following - let me know what debug to enable if you want me to try and catch where it's failing.
Comment
-
ISY Firmware now has Letter in it and crashing the plugin
Bob:
Your plugin has been a life saver and has been great.
I just upgraded my ISY to 5.0.10E to resolve issues with the Weather module not working. However, this seems to crash your plugin, as it's expecting a numeric firmware version number.
Output from crash:
Code:Plugin: ISYInsteon Instance: 3.0.0.50 starting... ISYInsteon Connecting to server at 127.0.0.1... Creating isy class instance: [192.168.1.4] Connected to HomeSeer at ip address 127.0.0.1 Host API version = 3 Callback API version = 3 ISYInsteon 3.0.0.50 will expire on 5/20/2018 8:00:00 AM ISYInsteon Unregistered. ISYInsteon Connected, waiting to be initialized... Unhandled Exception: System.FormatException: Input string was not in a correct f ormat. at System.Number.StringToNumber(String str, NumberStyles options, NumberBuffe r& number, NumberFormatInfo info, Boolean parseDecimal) at System.Number.ParseInt32(String s, NumberStyles style, NumberFormatInfo in fo) at ISYCommon.isy.FirmwareVersion(String ver_str) at ISYCommon.isy.Initialize(String username, String password) at HSPI_ISYInsteon.ISYInsteon.StartISY(String uname, String pword, String ip, Boolean restart) at HSPI_ISYInsteon.ISYInsteon.StartISYThread() at System.Threading.ThreadHelper.ThreadStart_Context(Object state) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionCo ntext, ContextCallback callback, Object state, Boolean preserveSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, C ontextCallback callback, Object state, Boolean preserveSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, C ontextCallback callback, Object state) at System.Threading.ThreadHelper.ThreadStart()
I look forward to being able to buy the plugin to support your time and effort!
Thanks,
James
Comment
-
Originally posted by tenroc2o0o View PostBob:
I just upgraded my ISY to 5.0.10E to resolve issues with the Weather module not working. However, this seems to crash your plugin, as it's expecting a numeric firmware version number.
I just uploaded 3.0.0.51 that should fix this so give it a try and verify for me.
grtaylor,
See if .51 helps with your issue too. I tried to replicate your problem but wasn't able to. I did make a small change to ignore creating scene associations between scene controller and members if there are no members because that seemed like it could be a problem.
Comment
-
Originally posted by chrkov View PostHey Bob,
On the .50 update, curious as to what "- Create device associations between scene devices and the scene members" does for us?
Chris
Comment
Comment